{"title":"Carbide Burrs","description":"\u003cp\u003eSolid tungsten carbide burrs for deburring, weld blending, die work and shaping metal. We stock Walter's heavy-duty 01V range and Drillco's 7000 sets, in double cut for steel and stainless, aluminum cut for soft metals, and a harder grade for hardened alloy.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePicking a cut.\u003c\/strong\u003e Double cut has two sets of crossed flutes: it breaks the chip small, grabs less and leaves a finer finish, which is why it is the default on ferrous metal. Single cut has one set of flutes and takes a bigger bite, for faster removal where finish matters less. Aluminum cut has widely spaced open flutes so soft metal clears instead of welding itself into the tool — use it on aluminum, brass, copper, magnesium and zinc.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePicking a head.\u003c\/strong\u003e SA cylindrical for flat work and deburring, SB for interior contours, SC ball nose for surface milling, SD ball and SE egg for cavities, SF and SG tree shapes for narrow contour work, SH flame for curves, SL and SM cones for angles, SN inverted cone for cutting from behind, SK for countersinking.\u003c\/p\u003e\u003ch3\u003eRunning them safely\u003c\/h3\u003e\u003cp\u003eSpeed is set by the burr diameter, not the grinder: 70,000 RPM at 1\/4\" down to 40,000 RPM at 5\/8\". The 6\" long series runs at half those figures and must never go below 20,000 RPM. Keep the feed light and let the flutes cut — pushing a burr blues the work and rounds the teeth off.\u003c\/p\u003e\u003cp\u003eFree shipping on orders over $200. Trade accounts can reorder in a click from \u003ca href=\"\/pages\/my-toolbox\"\u003eMy Toolbox\u003c\/a\u003e, or call (833) 438-6657.\u003c\/p\u003e","products":[{"product_id":"01v001","title":"1\/4\" x 5\/8\" SA-1 Cylindrical Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SA-1: a 1\/4\" cylindrical head with a 5\/8\" length of cut on a 1\/4\" shank. Deburring and flat surface work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SA-1 — Cylindrical\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 5\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 70,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V001\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685410906350,"sku":"01V001","price":44.18,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v001.jpg?v=1791226988"},{"product_id":"01v002","title":"3\/8\" x 3\/4\" SA-3 Cylindrical Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SA-3: a 3\/8\" cylindrical head with a 3\/4\" length of cut on a 1\/4\" shank. Deburring and flat surface work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SA-3 — Cylindrical\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 3\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 3\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 66,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V002\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685411299566,"sku":"01V002","price":59.31,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v002.jpg?v=1791226990"},{"product_id":"01v003","title":"3\/8\" x 3\/4\" SA-3 Cylindrical Carbide Burr, Aluminum Cut","description":"\u003cp\u003eAluminum cut burrs have widely spaced, single-direction flutes with a lot of chip clearance, and that geometry is the whole difference. Soft metals smear and weld themselves into a standard burr until it stops cutting and starts rubbing; an open flute throws the chip clear and keeps cutting. Use these on aluminum, brass, copper, magnesium, zinc and carbon fibre. They will cut steel, but a double cut burr will do it better and last longer, so keep the two apart rather than treating one as a general-purpose tool. This is the SA-3: a 3\/8\" cylindrical head with a 3\/4\" length of cut on a 1\/4\" shank. Deburring and flat surface work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SA-3 — Cylindrical\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 3\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 3\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Aluminum \/ Non-Ferrous Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 66,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V003\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eOpen, single-direction flutes that shed soft-metal chips\u003c\/li\u003e\n                \u003cli\u003eResists loading and clogging on aluminum\u003c\/li\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring aluminum and other soft metals\u003c\/li\u003e\n                \u003cli\u003eWeld blending on aluminum\u003c\/li\u003e\n                \u003cli\u003ePorting and shaping castings\u003c\/li\u003e\n                \u003cli\u003eWork where a standard burr loads up and stops cutting\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eAluminum\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eCopper\u003c\/li\u003e\n                \u003cli\u003eMagnesium\u003c\/li\u003e\n                \u003cli\u003eZinc\u003c\/li\u003e\n                \u003cli\u003eCarbon Fiber\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685411692782,"sku":"01V003","price":100.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v003_7a970a23-e8cd-45f4-86a8-6873253fc8cc.jpg?v=1791226991"},{"product_id":"01v004","title":"1\/2\" x 1\" SA-5 Cylindrical Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SA-5: a 1\/2\" cylindrical head with a 1\" length of cut on a 1\/4\" shank. Deburring and flat surface work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SA-5 — Cylindrical\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 50,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V004\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685412085998,"sku":"01V004","price":88.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v004_c7bf1fc2-eb79-4503-94b0-9ebccf7750d3.jpg?v=1791226992"},{"product_id":"01v005","title":"1\/4\" x 5\/8\" SC-1 Cylindrical Ball Nose Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SC-1: a 1\/4\" cylindrical ball nose head with a 5\/8\" length of cut on a 1\/4\" shank. Surface milling and contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SC-1 — Cylindrical Ball Nose\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 5\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 70,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V005\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685412511982,"sku":"01V005","price":48.12,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v005_3569b6e5-2add-4e14-9f50-0139ee2d5c89.jpg?v=1791226993"},{"product_id":"01v006","title":"3\/8\" x 3\/4\" SC-3 Cylindrical Ball Nose Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SC-3: a 3\/8\" cylindrical ball nose head with a 3\/4\" length of cut on a 1\/4\" shank. Surface milling and contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SC-3 — Cylindrical Ball Nose\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 3\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 3\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 66,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V006\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685412741358,"sku":"01V006","price":65.35,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v006_223e79eb-a1f1-4cca-800c-7e50a8582284.jpg?v=1791226995"},{"product_id":"01v007","title":"1\/2\" x 1\" SC-5 Cylindrical Ball Nose Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SC-5: a 1\/2\" cylindrical ball nose head with a 1\" length of cut on a 1\/4\" shank. Surface milling and contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SC-5 — Cylindrical Ball Nose\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 50,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V007\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685413363950,"sku":"01V007","price":100.77,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v007.jpg?v=1791226997"},{"product_id":"01v008","title":"1\/2\" x 1\" SC-5 Cylindrical Ball Nose Carbide Burr, Aluminum Cut","description":"\u003cp\u003eAluminum cut burrs have widely spaced, single-direction flutes with a lot of chip clearance, and that geometry is the whole difference. Soft metals smear and weld themselves into a standard burr until it stops cutting and starts rubbing; an open flute throws the chip clear and keeps cutting. Use these on aluminum, brass, copper, magnesium, zinc and carbon fibre. They will cut steel, but a double cut burr will do it better and last longer, so keep the two apart rather than treating one as a general-purpose tool. This is the SC-5: a 1\/2\" cylindrical ball nose head with a 1\" length of cut on a 1\/4\" shank. Surface milling and contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SC-5 — Cylindrical Ball Nose\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Aluminum \/ Non-Ferrous Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 50,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V008\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eOpen, single-direction flutes that shed soft-metal chips\u003c\/li\u003e\n                \u003cli\u003eResists loading and clogging on aluminum\u003c\/li\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring aluminum and other soft metals\u003c\/li\u003e\n                \u003cli\u003eWeld blending on aluminum\u003c\/li\u003e\n                \u003cli\u003ePorting and shaping castings\u003c\/li\u003e\n                \u003cli\u003eWork where a standard burr loads up and stops cutting\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eAluminum\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eCopper\u003c\/li\u003e\n                \u003cli\u003eMagnesium\u003c\/li\u003e\n                \u003cli\u003eZinc\u003c\/li\u003e\n                \u003cli\u003eCarbon Fiber\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685413986542,"sku":"01V008","price":174.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v008.jpg?v=1791226998"},{"product_id":"01v009","title":"1\/4\" x 7\/32\" SD-1 Ball Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SD-1: a 1\/4\" ball head with a 7\/32\" length of cut on a 1\/4\" shank. Surface milling, deburring and contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SD-1 — Ball\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 7\/32\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 70,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V009\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685414379758,"sku":"01V009","price":47.22,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v009.jpg?v=1791226999"},{"product_id":"01v010","title":"3\/8\" x 5\/16\" SD-3 Ball Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SD-3: a 3\/8\" ball head with a 5\/16\" length of cut on a 1\/4\" shank. Surface milling, deburring and contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SD-3 — Ball\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 3\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 5\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 66,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V010\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685414510830,"sku":"01V010","price":48.12,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v010.jpg?v=1791227001"},{"product_id":"01v011","title":"5\/8\" x 9\/16\" SD-6 Ball Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SD-6: a 5\/8\" ball head with a 9\/16\" length of cut on a 1\/4\" shank. Surface milling, deburring and contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SD-6 — Ball\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 5\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 9\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 40,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V011\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685414674670,"sku":"01V011","price":87.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v011.jpg?v=1791227002"},{"product_id":"01v013","title":"1\/2\" x 1\" SG-5 Pointed Tree Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SG-5: a 1\/2\" pointed tree head with a 1\" length of cut on a 1\/4\" shank. Surface milling and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SG-5 — Pointed Tree\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 50,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V013\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685414838510,"sku":"01V013","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v013_e8233209-9fbc-4f12-a1fd-9f25684bbc86.jpg?v=1791227003"},{"product_id":"01v014","title":"3\/8\" x 3\/4\" SF-3 Round Nose Tree Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SF-3: a 3\/8\" round nose tree head with a 3\/4\" length of cut on a 1\/4\" shank. Narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SF-3 — Round Nose Tree\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 3\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 3\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 66,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V014\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685415002350,"sku":"01V014","price":62.18,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v014.jpg?v=1791227005"},{"product_id":"01v015","title":"1\/2\" x 1\" SF-5 Round Nose Tree Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SF-5: a 1\/2\" round nose tree head with a 1\" length of cut on a 1\/4\" shank. Narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SF-5 — Round Nose Tree\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 50,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V015\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685415166190,"sku":"01V015","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v015.jpg?v=1791227006"},{"product_id":"01v016","title":"1\/2\" x 1\" SF-5 Round Nose Tree Carbide Burr, Aluminum Cut","description":"\u003cp\u003eAluminum cut burrs have widely spaced, single-direction flutes with a lot of chip clearance, and that geometry is the whole difference. Soft metals smear and weld themselves into a standard burr until it stops cutting and starts rubbing; an open flute throws the chip clear and keeps cutting. Use these on aluminum, brass, copper, magnesium, zinc and carbon fibre. They will cut steel, but a double cut burr will do it better and last longer, so keep the two apart rather than treating one as a general-purpose tool. This is the SF-5: a 1\/2\" round nose tree head with a 1\" length of cut on a 1\/4\" shank. Narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SF-5 — Round Nose Tree\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Aluminum \/ Non-Ferrous Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 50,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V016\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eOpen, single-direction flutes that shed soft-metal chips\u003c\/li\u003e\n                \u003cli\u003eResists loading and clogging on aluminum\u003c\/li\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring aluminum and other soft metals\u003c\/li\u003e\n                \u003cli\u003eWeld blending on aluminum\u003c\/li\u003e\n                \u003cli\u003ePorting and shaping castings\u003c\/li\u003e\n                \u003cli\u003eWork where a standard burr loads up and stops cutting\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eAluminum\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eCopper\u003c\/li\u003e\n                \u003cli\u003eMagnesium\u003c\/li\u003e\n                \u003cli\u003eZinc\u003c\/li\u003e\n                \u003cli\u003eCarbon Fiber\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685415297262,"sku":"01V016","price":157.35,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v016.jpg?v=1791227008"},{"product_id":"01v017","title":"1\/4\" x 5\/8\" SL-1 Cone, 14° Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SL-1: a 1\/4\" cone, 14° head with a 5\/8\" length of cut on a 1\/4\" shank. Surface machining and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SL-1 — Cone, 14°\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 5\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 70,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V017\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685415428334,"sku":"01V017","price":53.57,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v017.jpg?v=1791227009"},{"product_id":"01v018","title":"1\/2\" x 7\/8\" SM-5 Conical Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SM-5: a 1\/2\" conical head with a 7\/8\" length of cut on a 1\/4\" shank. Surface machining and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SM-5 — Conical\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 7\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 50,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V018\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685415690478,"sku":"01V018","price":100.77,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v018.jpg?v=1791227010"},{"product_id":"01v020","title":"1\/8\" x 9\/16\" SA-43 Cylindrical Carbide Burr, Double Cut, 1\/8\" Shank","description":"\u003cp\u003eThe 1\/8\" shank burrs are for detail work: die sinking, small radii, lettering, cleaning up inside a tapped hole or a tight internal corner where a 1\/4\" burr simply will not fit. They run in a pencil grinder or a die grinder with a 1\/8\" collet, and because the head is small they want high speed and almost no pressure — these snap if you lean on them. Double cut throughout, so they finish as well as they remove. This is the SA-43: a 1\/8\" cylindrical head with a 9\/16\" length of cut on a 1\/8\" shank. Deburring and flat surface work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SA-43 — Cylindrical\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 9\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V020\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each, minimum 2\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003e1\/8\" shank for pencil and die grinders\u003c\/li\u003e\n                \u003cli\u003eSolid tungsten carbide\u003c\/li\u003e\n                \u003cli\u003eDouble cut for a controlled finish\u003c\/li\u003e\n                \u003cli\u003eHigh speed, very light pressure\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDetail and die-sinking work\u003c\/li\u003e\n                \u003cli\u003eSmall radii and internal corners\u003c\/li\u003e\n                \u003cli\u003eCleaning up tapped and cross-drilled holes\u003c\/li\u003e\n                \u003cli\u003eEngraving and lettering\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003ePencil Grinder\u003c\/li\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eRotary Tool\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685415919854,"sku":"01V020","price":23.6,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v020_83cc628c-75c5-426e-a119-63a080065b46.jpg?v=1791227011"},{"product_id":"01v021","title":"1\/8\" x 1\/8\" SD-42 Ball Carbide Burr, Double Cut, 1\/8\" Shank","description":"\u003cp\u003eThe 1\/8\" shank burrs are for detail work: die sinking, small radii, lettering, cleaning up inside a tapped hole or a tight internal corner where a 1\/4\" burr simply will not fit. They run in a pencil grinder or a die grinder with a 1\/8\" collet, and because the head is small they want high speed and almost no pressure — these snap if you lean on them. Double cut throughout, so they finish as well as they remove. This is the SD-42: a 1\/8\" ball head with a 1\/8\" length of cut on a 1\/8\" shank. Surface milling, deburring and contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SD-42 — Ball\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V021\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each, minimum 2\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003e1\/8\" shank for pencil and die grinders\u003c\/li\u003e\n                \u003cli\u003eSolid tungsten carbide\u003c\/li\u003e\n                \u003cli\u003eDouble cut for a controlled finish\u003c\/li\u003e\n                \u003cli\u003eHigh speed, very light pressure\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDetail and die-sinking work\u003c\/li\u003e\n                \u003cli\u003eSmall radii and internal corners\u003c\/li\u003e\n                \u003cli\u003eCleaning up tapped and cross-drilled holes\u003c\/li\u003e\n                \u003cli\u003eEngraving and lettering\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003ePencil Grinder\u003c\/li\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eRotary Tool\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685416575214,"sku":"01V021","price":23.6,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v021_cf907d0b-5b3f-43c2-9ce4-8fbc3867941e.jpg?v=1791227013"},{"product_id":"01v022","title":"1\/8\" x 1\/2\" SF-42 Round Nose Tree Carbide Burr, Double Cut, 1\/8\" Shank","description":"\u003cp\u003eThe 1\/8\" shank burrs are for detail work: die sinking, small radii, lettering, cleaning up inside a tapped hole or a tight internal corner where a 1\/4\" burr simply will not fit. They run in a pencil grinder or a die grinder with a 1\/8\" collet, and because the head is small they want high speed and almost no pressure — these snap if you lean on them. Double cut throughout, so they finish as well as they remove. This is the SF-42: a 1\/8\" round nose tree head with a 1\/2\" length of cut on a 1\/8\" shank. Narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SF-42 — Round Nose Tree\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V022\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each, minimum 2\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003e1\/8\" shank for pencil and die grinders\u003c\/li\u003e\n                \u003cli\u003eSolid tungsten carbide\u003c\/li\u003e\n                \u003cli\u003eDouble cut for a controlled finish\u003c\/li\u003e\n                \u003cli\u003eHigh speed, very light pressure\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDetail and die-sinking work\u003c\/li\u003e\n                \u003cli\u003eSmall radii and internal corners\u003c\/li\u003e\n                \u003cli\u003eCleaning up tapped and cross-drilled holes\u003c\/li\u003e\n                \u003cli\u003eEngraving and lettering\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003ePencil Grinder\u003c\/li\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eRotary Tool\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685417132270,"sku":"01V022","price":23.6,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v022_78228c60-85b3-475a-a018-a089302dd215.jpg?v=1791227014"},{"product_id":"01v023","title":"1\/8\" x 1\/2\" SG-44 Pointed Tree Carbide Burr, Double Cut, 1\/8\" Shank","description":"\u003cp\u003eThe 1\/8\" shank burrs are for detail work: die sinking, small radii, lettering, cleaning up inside a tapped hole or a tight internal corner where a 1\/4\" burr simply will not fit. They run in a pencil grinder or a die grinder with a 1\/8\" collet, and because the head is small they want high speed and almost no pressure — these snap if you lean on them. Double cut throughout, so they finish as well as they remove. This is the SG-44: a 1\/8\" pointed tree head with a 1\/2\" length of cut on a 1\/8\" shank. Surface milling and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SG-44 — Pointed Tree\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V023\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each, minimum 2\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003e1\/8\" shank for pencil and die grinders\u003c\/li\u003e\n                \u003cli\u003eSolid tungsten carbide\u003c\/li\u003e\n                \u003cli\u003eDouble cut for a controlled finish\u003c\/li\u003e\n                \u003cli\u003eHigh speed, very light pressure\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDetail and die-sinking work\u003c\/li\u003e\n                \u003cli\u003eSmall radii and internal corners\u003c\/li\u003e\n                \u003cli\u003eCleaning up tapped and cross-drilled holes\u003c\/li\u003e\n                \u003cli\u003eEngraving and lettering\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003ePencil Grinder\u003c\/li\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eRotary Tool\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685417459950,"sku":"01V023","price":23.6,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v023.jpg?v=1791227016"},{"product_id":"01v024","title":"1\/8\" x 1\/2\" SL-42 Cone, 14° Carbide Burr, Double Cut, 1\/8\" Shank","description":"\u003cp\u003eThe 1\/8\" shank burrs are for detail work: die sinking, small radii, lettering, cleaning up inside a tapped hole or a tight internal corner where a 1\/4\" burr simply will not fit. They run in a pencil grinder or a die grinder with a 1\/8\" collet, and because the head is small they want high speed and almost no pressure — these snap if you lean on them. Double cut throughout, so they finish as well as they remove. This is the SL-42: a 1\/8\" cone, 14° head with a 1\/2\" length of cut on a 1\/8\" shank. Surface machining and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SL-42 — Cone, 14°\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V024\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each, minimum 2\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003e1\/8\" shank for pencil and die grinders\u003c\/li\u003e\n                \u003cli\u003eSolid tungsten carbide\u003c\/li\u003e\n                \u003cli\u003eDouble cut for a controlled finish\u003c\/li\u003e\n                \u003cli\u003eHigh speed, very light pressure\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDetail and die-sinking work\u003c\/li\u003e\n                \u003cli\u003eSmall radii and internal corners\u003c\/li\u003e\n                \u003cli\u003eCleaning up tapped and cross-drilled holes\u003c\/li\u003e\n                \u003cli\u003eEngraving and lettering\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003ePencil Grinder\u003c\/li\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eRotary Tool\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685417885934,"sku":"01V024","price":23.6,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v024.jpg?v=1791227017"},{"product_id":"01v025","title":"1\/8\" x 7\/16\" SM-42 Conical Carbide Burr, Double Cut, 1\/8\" Shank","description":"\u003cp\u003eThe 1\/8\" shank burrs are for detail work: die sinking, small radii, lettering, cleaning up inside a tapped hole or a tight internal corner where a 1\/4\" burr simply will not fit. They run in a pencil grinder or a die grinder with a 1\/8\" collet, and because the head is small they want high speed and almost no pressure — these snap if you lean on them. Double cut throughout, so they finish as well as they remove. This is the SM-42: a 1\/8\" conical head with a 7\/16\" length of cut on a 1\/8\" shank. Surface machining and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SM-42 — Conical\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 7\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V025\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each, minimum 2\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003e1\/8\" shank for pencil and die grinders\u003c\/li\u003e\n                \u003cli\u003eSolid tungsten carbide\u003c\/li\u003e\n                \u003cli\u003eDouble cut for a controlled finish\u003c\/li\u003e\n                \u003cli\u003eHigh speed, very light pressure\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDetail and die-sinking work\u003c\/li\u003e\n                \u003cli\u003eSmall radii and internal corners\u003c\/li\u003e\n                \u003cli\u003eCleaning up tapped and cross-drilled holes\u003c\/li\u003e\n                \u003cli\u003eEngraving and lettering\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003ePencil Grinder\u003c\/li\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eRotary Tool\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685418279150,"sku":"01V025","price":23.6,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v025.jpg?v=1791227018"},{"product_id":"01v026","title":"1\/2\" x 7\/16\" SD-5 Ball Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SD-5: a 1\/2\" ball head with a 7\/16\" length of cut on a 1\/4\" shank. Surface milling, deburring and contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SD-5 — Ball\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 7\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 50,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V026\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685418705134,"sku":"01V026","price":66.11,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v026.jpg?v=1791227020"},{"product_id":"01v027","title":"3\/8\" x 5\/8\" SE-3 Egg Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SE-3: a 3\/8\" egg head with a 5\/8\" length of cut on a 1\/4\" shank. Contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SE-3 — Egg\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 3\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 5\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 66,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V027\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685419294958,"sku":"01V027","price":59.31,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v027.jpg?v=1791227021"},{"product_id":"01v028","title":"1\/2\" x 7\/8\" SE-5 Egg Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SE-5: a 1\/2\" egg head with a 7\/8\" length of cut on a 1\/4\" shank. Contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SE-5 — Egg\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 7\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 50,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V028\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685419655406,"sku":"01V028","price":88.22,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v028_f1ae32b4-0b00-4d2e-9bdf-4bd506e0df14.jpg?v=1791227022"},{"product_id":"01v029","title":"5\/16\" x 3\/4\" SH-3 Flame Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SH-3: a 5\/16\" flame head with a 3\/4\" length of cut on a 1\/4\" shank. Contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SH-3 — Flame\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 5\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 3\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 68,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V029\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685420146926,"sku":"01V029","price":63.86,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v029_9fd792bb-003b-4b74-9972-b534a1236411.jpg?v=1791227024"},{"product_id":"01v030","title":"1\/2\" x 1-1\/4\" SH-5 Flame Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SH-5: a 1\/2\" flame head with a 1-1\/4\" length of cut on a 1\/4\" shank. Contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SH-5 — Flame\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1-1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 50,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V030\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685420671214,"sku":"01V030","price":122.88,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v030.jpg?v=1791227029"},{"product_id":"01v031","title":"3\/8\" x 1-1\/16\" SL-3 Cone, 14° Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SL-3: a 3\/8\" cone, 14° head with a 1-1\/16\" length of cut on a 1\/4\" shank. Surface machining and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SL-3 — Cone, 14°\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 3\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1-1\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 66,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V031\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685421129966,"sku":"01V031","price":73.22,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v031_581bcecd-a10b-4187-8c85-65c923e67a78.jpg?v=1791227026"},{"product_id":"01v032","title":"1\/2\" x 1-1\/8\" SL-4 Cone, 14° Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SL-4: a 1\/2\" cone, 14° head with a 1-1\/8\" length of cut on a 1\/4\" shank. Surface machining and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SL-4 — Cone, 14°\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1-1\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 50,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V032\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685421719790,"sku":"01V032","price":87.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v032.jpg?v=1791227028"},{"product_id":"01v033","title":"1\/2\" x 1\" SC-5 Cylindrical Ball Nose Carbide Burr, Double Cut, Hard Alloy","description":"\u003cp\u003eA harder carbide grade for the material that kills ordinary burrs: hardened and heat-treated steel, high-nickel alloys, work-hardened stainless and anything in the 45–60 Rc range. The trade-off is that a harder grade is also more brittle, so these want a rigid setup, a steady feed and no side loading — run them straight into the work rather than levering sideways. This is the SC-5: a 1\/2\" cylindrical ball nose head with a 1\" length of cut on a 1\/4\" shank. Surface milling and contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SC-5 — Cylindrical Ball Nose\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 50,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V033\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eHarder carbide grade for 45–60 Rc material\u003c\/li\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eHardened and heat-treated steel\u003c\/li\u003e\n                \u003cli\u003eHigh-nickel and work-hardened stainless\u003c\/li\u003e\n                \u003cli\u003eTool and die rework\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685422178542,"sku":"01V033","price":107.89,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v033.jpg?v=1791227030"},{"product_id":"01v034","title":"1\/2\" x 1\" SF-5 Round Nose Tree Carbide Burr, Double Cut, Hard Alloy","description":"\u003cp\u003eA harder carbide grade for the material that kills ordinary burrs: hardened and heat-treated steel, high-nickel alloys, work-hardened stainless and anything in the 45–60 Rc range. The trade-off is that a harder grade is also more brittle, so these want a rigid setup, a steady feed and no side loading — run them straight into the work rather than levering sideways. This is the SF-5: a 1\/2\" round nose tree head with a 1\" length of cut on a 1\/4\" shank. Narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SF-5 — Round Nose Tree\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 50,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V034\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eHarder carbide grade for 45–60 Rc material\u003c\/li\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eHardened and heat-treated steel\u003c\/li\u003e\n                \u003cli\u003eHigh-nickel and work-hardened stainless\u003c\/li\u003e\n                \u003cli\u003eTool and die rework\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685422276846,"sku":"01V034","price":99.28,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v034_7038a780-b172-4f3f-8b4b-46e8f1ea6cda.jpg?v=1791227031"},{"product_id":"01v035","title":"1\/2\" x 1-1\/8\" SL-4 Cone, 14° Carbide Burr, Double Cut, Hard Alloy","description":"\u003cp\u003eA harder carbide grade for the material that kills ordinary burrs: hardened and heat-treated steel, high-nickel alloys, work-hardened stainless and anything in the 45–60 Rc range. The trade-off is that a harder grade is also more brittle, so these want a rigid setup, a steady feed and no side loading — run them straight into the work rather than levering sideways. This is the SL-4: a 1\/2\" cone, 14° head with a 1-1\/8\" length of cut on a 1\/4\" shank. Surface machining and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SL-4 — Cone, 14°\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1-1\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 50,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V035\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eHarder carbide grade for 45–60 Rc material\u003c\/li\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eHardened and heat-treated steel\u003c\/li\u003e\n                \u003cli\u003eHigh-nickel and work-hardened stainless\u003c\/li\u003e\n                \u003cli\u003eTool and die rework\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685422637294,"sku":"01V035","price":104.72,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v035_7bfa201f-43e4-4c6b-beaf-f29ee1008836.jpg?v=1791227032"},{"product_id":"01v036","title":"3\/8\" x 1-1\/4\" SL-3 Cone, 14° Carbide Burr, Aluminum Cut","description":"\u003cp\u003eAluminum cut burrs have widely spaced, single-direction flutes with a lot of chip clearance, and that geometry is the whole difference. Soft metals smear and weld themselves into a standard burr until it stops cutting and starts rubbing; an open flute throws the chip clear and keeps cutting. Use these on aluminum, brass, copper, magnesium, zinc and carbon fibre. They will cut steel, but a double cut burr will do it better and last longer, so keep the two apart rather than treating one as a general-purpose tool. This is the SL-3: a 3\/8\" cone, 14° head with a 1-1\/4\" length of cut on a 1\/4\" shank. Surface machining and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SL-3 — Cone, 14°\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 3\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1-1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Aluminum \/ Non-Ferrous Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 66,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V036\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eOpen, single-direction flutes that shed soft-metal chips\u003c\/li\u003e\n                \u003cli\u003eResists loading and clogging on aluminum\u003c\/li\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring aluminum and other soft metals\u003c\/li\u003e\n                \u003cli\u003eWeld blending on aluminum\u003c\/li\u003e\n                \u003cli\u003ePorting and shaping castings\u003c\/li\u003e\n                \u003cli\u003eWork where a standard burr loads up and stops cutting\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eAluminum\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eCopper\u003c\/li\u003e\n                \u003cli\u003eMagnesium\u003c\/li\u003e\n                \u003cli\u003eZinc\u003c\/li\u003e\n                \u003cli\u003eCarbon Fiber\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685423194350,"sku":"01V036","price":100.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v036.jpg?v=1791227034"},{"product_id":"01v037","title":"5\/16\" x 3\/4\" SA-2 Cylindrical Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SA-2: a 5\/16\" cylindrical head with a 3\/4\" length of cut on a 1\/4\" shank. Deburring and flat surface work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SA-2 — Cylindrical\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 5\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 3\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 70,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V037\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685423587566,"sku":"01V037","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v037_dba18242-f89a-4924-82b9-d11b61c7a673.jpg?v=1791227035"},{"product_id":"01v038","title":"7\/16\" x 1\" SA-4 Cylindrical Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SA-4: a 7\/16\" cylindrical head with a 1\" length of cut on a 1\/4\" shank. Deburring and flat surface work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SA-4 — Cylindrical\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 7\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 58,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V038\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685423751406,"sku":"01V038","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v038_d1c00cd9-6e1b-424e-9d42-d433295c23ae.jpg?v=1791227036"},{"product_id":"01v039","title":"5\/16\" x 3\/4\" SC-2 Cylindrical Ball Nose Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SC-2: a 5\/16\" cylindrical ball nose head with a 3\/4\" length of cut on a 1\/4\" shank. Surface milling and contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SC-2 — Cylindrical Ball Nose\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 5\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 3\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 68,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V039\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685423948014,"sku":"01V039","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v039_bb061b7a-ea43-45fd-83d1-3fd373cf6c07.jpg?v=1791227038"},{"product_id":"01v040","title":"7\/16\" x 1\" SC-4 Cylindrical Ball Nose Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SC-4: a 7\/16\" cylindrical ball nose head with a 1\" length of cut on a 1\/4\" shank. Surface milling and contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SC-4 — Cylindrical Ball Nose\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 7\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 58,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V040\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685424046318,"sku":"01V040","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v040.jpg?v=1791227039"},{"product_id":"01v041","title":"1\/4\" x 5\/8\" SF-1 Round Nose Tree Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SF-1: a 1\/4\" round nose tree head with a 5\/8\" length of cut on a 1\/4\" shank. Narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SF-1 — Round Nose Tree\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 5\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 70,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V041\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685424931054,"sku":"01V041","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v041_8ac0759e-d617-4d8f-a0ba-c66cd8579bdd.jpg?v=1791227040"},{"product_id":"01v042","title":"5\/16\" x 5\/8\" SF-2 Round Nose Tree Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SF-2: a 5\/16\" round nose tree head with a 5\/8\" length of cut on a 1\/4\" shank. Narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SF-2 — Round Nose Tree\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 5\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 5\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 68,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V042\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685425225966,"sku":"01V042","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v042.jpg?v=1791227042"},{"product_id":"01v043","title":"7\/16\" x 1\" SF-4 Round Nose Tree Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SF-4: a 7\/16\" round nose tree head with a 1\" length of cut on a 1\/4\" shank. Narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SF-4 — Round Nose Tree\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 7\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 58,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V043\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685425455342,"sku":"01V043","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v043_6df86843-39ff-4bcf-9196-2acda05f1c08.jpg?v=1791227043"},{"product_id":"01v044","title":"1\/4\" x 5\/8\" SG-1 Pointed Tree Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SG-1: a 1\/4\" pointed tree head with a 5\/8\" length of cut on a 1\/4\" shank. Surface milling and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SG-1 — Pointed Tree\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 5\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 70,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V044\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685425717486,"sku":"01V044","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v044.jpg?v=1791227045"},{"product_id":"01v045","title":"5\/16\" x 3\/4\" SG-2 Pointed Tree Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SG-2: a 5\/16\" pointed tree head with a 3\/4\" length of cut on a 1\/4\" shank. Surface milling and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SG-2 — Pointed Tree\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 5\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 3\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 68,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V045\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685426077934,"sku":"01V045","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v045.jpg?v=1791227046"},{"product_id":"01v046","title":"3\/8\" x 3\/4\" SG-3 Pointed Tree Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SG-3: a 3\/8\" pointed tree head with a 3\/4\" length of cut on a 1\/4\" shank. Surface milling and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SG-3 — Pointed Tree\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 3\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 3\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 66,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V046\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685426405614,"sku":"01V046","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v046.jpg?v=1791227047"},{"product_id":"01v047","title":"1\/4\" x 1\/2\" SM-1 Conical Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SM-1: a 1\/4\" conical head with a 1\/2\" length of cut on a 1\/4\" shank. Surface machining and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SM-1 — Conical\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 70,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V047\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685426798830,"sku":"01V047","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v047_15b42fbf-6b79-4cee-95c0-4f44de20ecfb.jpg?v=1791227049"},{"product_id":"01v048","title":"1\/4\" x 3\/4\" SM-2 Conical Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SM-2: a 1\/4\" conical head with a 3\/4\" length of cut on a 1\/4\" shank. Surface machining and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SM-2 — Conical\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 3\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 70,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V048\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685427224814,"sku":"01V048","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v048.jpg?v=1791227050"},{"product_id":"01v049","title":"1\/4\" x 1\" SM-3 Conical Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SM-3: a 1\/4\" conical head with a 1\" length of cut on a 1\/4\" shank. Surface machining and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SM-3 — Conical\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 1\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 70,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V049\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685427454190,"sku":"01V049","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v049.jpg?v=1791227052"},{"product_id":"01v050","title":"3\/8\" x 5\/8\" SM-4 Conical Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SM-4: a 3\/8\" conical head with a 5\/8\" length of cut on a 1\/4\" shank. Surface machining and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SM-4 — Conical\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 3\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 5\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 66,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V050\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685427847406,"sku":"01V050","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v050.jpg?v=1791227053"},{"product_id":"01v051","title":"5\/16\" x 7\/8\" SL-2 Cone, 14° Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SL-2: a 5\/16\" cone, 14° head with a 7\/8\" length of cut on a 1\/4\" shank. Surface machining and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SL-2 — Cone, 14°\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 5\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 7\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 68,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V051\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685428044014,"sku":"01V051","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v051.jpg?v=1791227054"},{"product_id":"01v052","title":"5\/8\" x 3\/16\" SL-5 Cone, 14° Carbide Burr, Double Cut","description":"\u003cp\u003eWalter's 01V burrs are the heavy-duty end of the carbide burr range: solid tungsten carbide heads on a 1\/4\" shank, brazed with a high-strength joint that is built to stop the head snapping off the shank under load. Double cut means two sets of flutes crossing each other, which breaks the swarf into small chips instead of long curls — you get more control, a finer finish and far less grabbing than a single cut burr, which is why it is the cut most shops run on steel and stainless. Walter grinds these for concentricity and balance, so they run true without the vibration that chatters a finish and shortens tool life. This is the SL-5: a 5\/8\" cone, 14° head with a 3\/16\" length of cut on a 1\/4\" shank. Surface machining and narrow contour work.\u003c\/p\u003e\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eHead style:\u003c\/strong\u003e SL-5 — Cone, 14°\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eBurr diameter:\u003c\/strong\u003e 5\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eLength of cut:\u003c\/strong\u003e 3\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank diameter:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCut:\u003c\/strong\u003e Double Cut\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Tungsten Carbide\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eMaximum speed:\u003c\/strong\u003e 40,000 RPM\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e Walter 01V052\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eCountry of origin:\u003c\/strong\u003e China\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e Each\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSolid tungsten carbide head\u003c\/li\u003e\n                \u003cli\u003eHigh-strength brazed joint, built to resist breakage\u003c\/li\u003e\n                \u003cli\u003eGround for concentricity and balance, so it runs without vibration\u003c\/li\u003e\n                \u003cli\u003eFlute geometry clears chips from tip to base\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eApplications:\u003c\/h3\u003e\n                \u003cli\u003eDeburring and edge breaking after machining\u003c\/li\u003e\n                \u003cli\u003eWeld dressing and blending\u003c\/li\u003e\n                \u003cli\u003eDie and mould work\u003c\/li\u003e\n                \u003cli\u003eOpening and shaping holes and slots\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eCarbon Steel\u003c\/li\u003e\n                \u003cli\u003eStainless Steel\u003c\/li\u003e\n                \u003cli\u003eHardened Steel (45–60 Rc)\u003c\/li\u003e\n                \u003cli\u003eNickel Chrome Steel\u003c\/li\u003e\n                \u003cli\u003eWeldments\u003c\/li\u003e\n                \u003cli\u003eCast Iron\u003c\/li\u003e\n                \u003cli\u003eTitanium\u003c\/li\u003e\n                \u003cli\u003eInconel\u003c\/li\u003e\n                \u003cli\u003eBrass\u003c\/li\u003e\n                \u003cli\u003eBronze\u003c\/li\u003e\n                \u003cli\u003eFiberglass\u003c\/li\u003e\n                \u003cli\u003eHard Rubber\u003c\/li\u003e\n                \u003cli\u003ePlastics\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eDie Grinder\u003c\/li\u003e\n                \u003cli\u003eAir Grinder\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Walter","offers":[{"title":"Default Title","offer_id":49685428273390,"sku":"01V052","price":92.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/walter-01v052_69110d8e-6c2e-47f0-9ccd-70b8bb92a7bc.jpg?v=1791227055"}],"url":"https:\/\/eldoradotools.com\/collections\/carbide-burrs.oembed?page=4","provider":"Eldorado Tools Inc","version":"1.0","type":"link"}