{"title":"Anchor \u0026 Concrete Screw Bits","description":"\u003cp\u003eEverything that goes in the hole before the hanger does. Stop drill bits that drill the exact depth a drop-in anchor needs, and the SDS-Plus driver that sets nail-in anchors without a hand hammer.\u003c\/p\u003e\n\u003cp\u003eA drop-in anchor only holds properly when the hole is the right depth: too deep and the anchor sits below the surface, too shallow and it stands proud. The stop lip on these bits takes the guesswork out of that, which matters most overhead, where pipe, duct, sprinkler line, strut and cable tray all hang from the deck. Running a bigger machine? The \u003ca href=\"https:\/\/eldoradotools.com\/products\/725max001\"\u003eSDS-Max to SDS-Plus adapter\u003c\/a\u003e takes these bits in an SDS-Max hammer.\u003c\/p\u003e","products":[{"product_id":"stp-413","title":"1\/4\" SDS-Plus Stop Drill Bit for 3\/16\" Drop-In Anchors","description":"\u003ch2\u003e1\/4\" SDS-Plus Stop Drill Bit for 3\/16\" Drop-In Anchors\u003c\/h2\u003e\n\u003cp\u003eITM\u003c\/p\u003e\n\n\u003cp\u003eA 1\/4\" SDS-Plus hammer bit with a stop lip that bottoms out at 11\/16\", the exact hole depth a 3\/16\" drop-in anchor needs. Drill until the lip touches the concrete and the hole is right: the anchor sits flush, the setting tool expands it properly, and the threaded rod pulls against the full cone.\u003c\/p\u003e\n\n\u003cp\u003eOverhead work is where that matters most. Hangers for pipe, duct, sprinkler line, strut and cable tray all land in a concrete deck, and a hole drilled too deep buries the anchor below the surface, while a shallow one stops the anchor short. The stop also keeps you from driving deeper than you need to, which is one less chance of hitting rebar. Carbide tipped, ANSI specification, sold individually.\u003c\/p\u003e\n\n\u003cp\u003eSetting hammer-in anchors on the same job? Use the \u003ca href=\"https:\/\/eldoradotools.com\/products\/sds-hd1\"\u003eSDS-Plus nail-in anchor driver\u003c\/a\u003e. Running a big SDS-Max hammer overhead? The \u003ca href=\"https:\/\/eldoradotools.com\/products\/725max001\"\u003eSDS-Max to SDS-Plus Adapter\u003c\/a\u003e takes these bits without a tool change.\u003c\/p\u003e\n\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eDrill size:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eDrill depth (stop):\u003c\/strong\u003e 11\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eFits drop-in anchor:\u003c\/strong\u003e 3\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank:\u003c\/strong\u003e SDS-Plus\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eTip:\u003c\/strong\u003e Carbide tipped\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eStandard:\u003c\/strong\u003e ANSI specification\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eStop lip prevents over-drilling\u003c\/li\u003e\n                \u003cli\u003eDrills the exact depth a drop-in anchor needs\u003c\/li\u003e\n                \u003cli\u003eLess likely to hit rebar\u003c\/li\u003e\n                \u003cli\u003eCarbide tipped for concrete, stone, brick and masonry\u003c\/li\u003e\n                \u003cli\u003eANSI specification\u003c\/li\u003e\n                \u003cli\u003eSold individually\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eConcrete\u003c\/li\u003e\n                \u003cli\u003eStone\u003c\/li\u003e\n                \u003cli\u003eBrick\u003c\/li\u003e\n                \u003cli\u003eMasonry\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eSDS-Plus Rotary Hammer\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"ITM","offers":[{"title":"Default Title","offer_id":49639983120622,"sku":"STP-413","price":15.39,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/itm-stp-sds-plus-stop-drill-bit.jpg?v=1790274150"},{"product_id":"stp-617","title":"3\/8\" SDS-Plus Stop Drill Bit for 1\/4\" Drop-In Anchors","description":"\u003ch2\u003e3\/8\" SDS-Plus Stop Drill Bit for 1\/4\" Drop-In Anchors\u003c\/h2\u003e\n\u003cp\u003eITM\u003c\/p\u003e\n\n\u003cp\u003eA 3\/8\" SDS-Plus hammer bit with a stop lip that bottoms out at 1-1\/16\", the exact hole depth a 1\/4\" drop-in anchor needs. Drill until the lip touches the concrete and the hole is right: the anchor sits flush, the setting tool expands it properly, and the threaded rod pulls against the full cone.\u003c\/p\u003e\n\n\u003cp\u003eOverhead work is where that matters most. Hangers for pipe, duct, sprinkler line, strut and cable tray all land in a concrete deck, and a hole drilled too deep buries the anchor below the surface, while a shallow one stops the anchor short. The stop also keeps you from driving deeper than you need to, which is one less chance of hitting rebar. Carbide tipped, ANSI specification, sold individually.\u003c\/p\u003e\n\n\u003cp\u003eSetting hammer-in anchors on the same job? Use the \u003ca href=\"https:\/\/eldoradotools.com\/products\/sds-hd1\"\u003eSDS-Plus nail-in anchor driver\u003c\/a\u003e. Running a big SDS-Max hammer overhead? The \u003ca href=\"https:\/\/eldoradotools.com\/products\/725max001\"\u003eSDS-Max to SDS-Plus Adapter\u003c\/a\u003e takes these bits without a tool change.\u003c\/p\u003e\n\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eDrill size:\u003c\/strong\u003e 3\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eDrill depth (stop):\u003c\/strong\u003e 1-1\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eFits drop-in anchor:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank:\u003c\/strong\u003e SDS-Plus\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eTip:\u003c\/strong\u003e Carbide tipped\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eStandard:\u003c\/strong\u003e ANSI specification\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eStop lip prevents over-drilling\u003c\/li\u003e\n                \u003cli\u003eDrills the exact depth a drop-in anchor needs\u003c\/li\u003e\n                \u003cli\u003eLess likely to hit rebar\u003c\/li\u003e\n                \u003cli\u003eCarbide tipped for concrete, stone, brick and masonry\u003c\/li\u003e\n                \u003cli\u003eANSI specification\u003c\/li\u003e\n                \u003cli\u003eSold individually\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eConcrete\u003c\/li\u003e\n                \u003cli\u003eStone\u003c\/li\u003e\n                \u003cli\u003eBrick\u003c\/li\u003e\n                \u003cli\u003eMasonry\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eSDS-Plus Rotary Hammer\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"ITM","offers":[{"title":"Default Title","offer_id":49639983251694,"sku":"STP-617","price":16.76,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/itm-stp-sds-plus-stop-drill-bit.jpg?v=1790274150"},{"product_id":"stp-813","title":"1\/2\" SDS-Plus Stop Drill Bit for 3\/8\" Short Drop-In Anchors","description":"\u003ch2\u003e1\/2\" SDS-Plus Stop Drill Bit for 3\/8\" Short Drop-In Anchors\u003c\/h2\u003e\n\u003cp\u003eITM\u003c\/p\u003e\n\n\u003cp\u003eA 1\/2\" SDS-Plus hammer bit with a stop lip that bottoms out at 13\/16\", the exact hole depth a 3\/8\" Short drop-in anchor needs. Drill until the lip touches the concrete and the hole is right: the anchor sits flush, the setting tool expands it properly, and the threaded rod pulls against the full cone.\u003c\/p\u003e\n\n\u003cp\u003eOverhead work is where that matters most. Hangers for pipe, duct, sprinkler line, strut and cable tray all land in a concrete deck, and a hole drilled too deep buries the anchor below the surface, while a shallow one stops the anchor short. The stop also keeps you from driving deeper than you need to, which is one less chance of hitting rebar. Carbide tipped, ANSI specification, sold individually.\u003c\/p\u003e\n\n\u003cp\u003eSetting hammer-in anchors on the same job? Use the \u003ca href=\"https:\/\/eldoradotools.com\/products\/sds-hd1\"\u003eSDS-Plus nail-in anchor driver\u003c\/a\u003e. Running a big SDS-Max hammer overhead? The \u003ca href=\"https:\/\/eldoradotools.com\/products\/725max001\"\u003eSDS-Max to SDS-Plus Adapter\u003c\/a\u003e takes these bits without a tool change.\u003c\/p\u003e\n\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eDrill size:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eDrill depth (stop):\u003c\/strong\u003e 13\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eFits drop-in anchor:\u003c\/strong\u003e 3\/8\" Short\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank:\u003c\/strong\u003e SDS-Plus\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eTip:\u003c\/strong\u003e Carbide tipped\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eStandard:\u003c\/strong\u003e ANSI specification\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eStop lip prevents over-drilling\u003c\/li\u003e\n                \u003cli\u003eDrills the exact depth a drop-in anchor needs\u003c\/li\u003e\n                \u003cli\u003eLess likely to hit rebar\u003c\/li\u003e\n                \u003cli\u003eCarbide tipped for concrete, stone, brick and masonry\u003c\/li\u003e\n                \u003cli\u003eANSI specification\u003c\/li\u003e\n                \u003cli\u003eSold individually\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eConcrete\u003c\/li\u003e\n                \u003cli\u003eStone\u003c\/li\u003e\n                \u003cli\u003eBrick\u003c\/li\u003e\n                \u003cli\u003eMasonry\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eSDS-Plus Rotary Hammer\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"ITM","offers":[{"title":"Default Title","offer_id":49639983317230,"sku":"STP-813","price":18.62,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/itm-stp-sds-plus-stop-drill-bit.jpg?v=1790274150"},{"product_id":"stp-827","title":"1\/2\" SDS-Plus Stop Drill Bit for 3\/8\" Drop-In Anchors","description":"\u003ch2\u003e1\/2\" SDS-Plus Stop Drill Bit for 3\/8\" Drop-In Anchors\u003c\/h2\u003e\n\u003cp\u003eITM\u003c\/p\u003e\n\n\u003cp\u003eA 1\/2\" SDS-Plus hammer bit with a stop lip that bottoms out at 1-11\/16\", the exact hole depth a 3\/8\" drop-in anchor needs. Drill until the lip touches the concrete and the hole is right: the anchor sits flush, the setting tool expands it properly, and the threaded rod pulls against the full cone.\u003c\/p\u003e\n\n\u003cp\u003eOverhead work is where that matters most. Hangers for pipe, duct, sprinkler line, strut and cable tray all land in a concrete deck, and a hole drilled too deep buries the anchor below the surface, while a shallow one stops the anchor short. The stop also keeps you from driving deeper than you need to, which is one less chance of hitting rebar. Carbide tipped, ANSI specification, sold individually.\u003c\/p\u003e\n\n\u003cp\u003eSetting hammer-in anchors on the same job? Use the \u003ca href=\"https:\/\/eldoradotools.com\/products\/sds-hd1\"\u003eSDS-Plus nail-in anchor driver\u003c\/a\u003e. Running a big SDS-Max hammer overhead? The \u003ca href=\"https:\/\/eldoradotools.com\/products\/725max001\"\u003eSDS-Max to SDS-Plus Adapter\u003c\/a\u003e takes these bits without a tool change.\u003c\/p\u003e\n\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eDrill size:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eDrill depth (stop):\u003c\/strong\u003e 1-11\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eFits drop-in anchor:\u003c\/strong\u003e 3\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank:\u003c\/strong\u003e SDS-Plus\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eTip:\u003c\/strong\u003e Carbide tipped\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eStandard:\u003c\/strong\u003e ANSI specification\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eStop lip prevents over-drilling\u003c\/li\u003e\n                \u003cli\u003eDrills the exact depth a drop-in anchor needs\u003c\/li\u003e\n                \u003cli\u003eLess likely to hit rebar\u003c\/li\u003e\n                \u003cli\u003eCarbide tipped for concrete, stone, brick and masonry\u003c\/li\u003e\n                \u003cli\u003eANSI specification\u003c\/li\u003e\n                \u003cli\u003eSold individually\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eConcrete\u003c\/li\u003e\n                \u003cli\u003eStone\u003c\/li\u003e\n                \u003cli\u003eBrick\u003c\/li\u003e\n                \u003cli\u003eMasonry\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eSDS-Plus Rotary Hammer\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"ITM","offers":[{"title":"Default Title","offer_id":49639983382766,"sku":"STP-827","price":19.55,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/itm-stp-sds-plus-stop-drill-bit.jpg?v=1790274150"},{"product_id":"stp-1019","title":"5\/8\" SDS-Plus Stop Drill Bit for 1\/2\" Short Drop-In Anchors","description":"\u003ch2\u003e5\/8\" SDS-Plus Stop Drill Bit for 1\/2\" Short Drop-In Anchors\u003c\/h2\u003e\n\u003cp\u003eITM\u003c\/p\u003e\n\n\u003cp\u003eA 5\/8\" SDS-Plus hammer bit with a stop lip that bottoms out at 1-3\/16\", the exact hole depth a 1\/2\" Short drop-in anchor needs. Drill until the lip touches the concrete and the hole is right: the anchor sits flush, the setting tool expands it properly, and the threaded rod pulls against the full cone.\u003c\/p\u003e\n\n\u003cp\u003eOverhead work is where that matters most. Hangers for pipe, duct, sprinkler line, strut and cable tray all land in a concrete deck, and a hole drilled too deep buries the anchor below the surface, while a shallow one stops the anchor short. The stop also keeps you from driving deeper than you need to, which is one less chance of hitting rebar. Carbide tipped, ANSI specification, sold individually.\u003c\/p\u003e\n\n\u003cp\u003eSetting hammer-in anchors on the same job? Use the \u003ca href=\"https:\/\/eldoradotools.com\/products\/sds-hd1\"\u003eSDS-Plus nail-in anchor driver\u003c\/a\u003e. Running a big SDS-Max hammer overhead? The \u003ca href=\"https:\/\/eldoradotools.com\/products\/725max001\"\u003eSDS-Max to SDS-Plus Adapter\u003c\/a\u003e takes these bits without a tool change.\u003c\/p\u003e\n\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eDrill size:\u003c\/strong\u003e 5\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eDrill depth (stop):\u003c\/strong\u003e 1-3\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eFits drop-in anchor:\u003c\/strong\u003e 1\/2\" Short\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank:\u003c\/strong\u003e SDS-Plus\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eTip:\u003c\/strong\u003e Carbide tipped\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eStandard:\u003c\/strong\u003e ANSI specification\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eStop lip prevents over-drilling\u003c\/li\u003e\n                \u003cli\u003eDrills the exact depth a drop-in anchor needs\u003c\/li\u003e\n                \u003cli\u003eLess likely to hit rebar\u003c\/li\u003e\n                \u003cli\u003eCarbide tipped for concrete, stone, brick and masonry\u003c\/li\u003e\n                \u003cli\u003eANSI specification\u003c\/li\u003e\n                \u003cli\u003eSold individually\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eConcrete\u003c\/li\u003e\n                \u003cli\u003eStone\u003c\/li\u003e\n                \u003cli\u003eBrick\u003c\/li\u003e\n                \u003cli\u003eMasonry\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eSDS-Plus Rotary Hammer\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"ITM","offers":[{"title":"Default Title","offer_id":49639983448302,"sku":"STP-1019","price":20.93,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/itm-stp-sds-plus-stop-drill-bit.jpg?v=1790274150"},{"product_id":"stp-1033","title":"5\/8\" SDS-Plus Stop Drill Bit for 1\/2\" Drop-In Anchors","description":"\u003ch2\u003e5\/8\" SDS-Plus Stop Drill Bit for 1\/2\" Drop-In Anchors\u003c\/h2\u003e\n\u003cp\u003eITM\u003c\/p\u003e\n\n\u003cp\u003eA 5\/8\" SDS-Plus hammer bit with a stop lip that bottoms out at 2-1\/16\", the exact hole depth a 1\/2\" drop-in anchor needs. Drill until the lip touches the concrete and the hole is right: the anchor sits flush, the setting tool expands it properly, and the threaded rod pulls against the full cone.\u003c\/p\u003e\n\n\u003cp\u003eOverhead work is where that matters most. Hangers for pipe, duct, sprinkler line, strut and cable tray all land in a concrete deck, and a hole drilled too deep buries the anchor below the surface, while a shallow one stops the anchor short. The stop also keeps you from driving deeper than you need to, which is one less chance of hitting rebar. Carbide tipped, ANSI specification, sold individually.\u003c\/p\u003e\n\n\u003cp\u003eSetting hammer-in anchors on the same job? Use the \u003ca href=\"https:\/\/eldoradotools.com\/products\/sds-hd1\"\u003eSDS-Plus nail-in anchor driver\u003c\/a\u003e. Running a big SDS-Max hammer overhead? The \u003ca href=\"https:\/\/eldoradotools.com\/products\/725max001\"\u003eSDS-Max to SDS-Plus Adapter\u003c\/a\u003e takes these bits without a tool change.\u003c\/p\u003e\n\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eDrill size:\u003c\/strong\u003e 5\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eDrill depth (stop):\u003c\/strong\u003e 2-1\/16\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eFits drop-in anchor:\u003c\/strong\u003e 1\/2\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank:\u003c\/strong\u003e SDS-Plus\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eTip:\u003c\/strong\u003e Carbide tipped\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eStandard:\u003c\/strong\u003e ANSI specification\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eStop lip prevents over-drilling\u003c\/li\u003e\n                \u003cli\u003eDrills the exact depth a drop-in anchor needs\u003c\/li\u003e\n                \u003cli\u003eLess likely to hit rebar\u003c\/li\u003e\n                \u003cli\u003eCarbide tipped for concrete, stone, brick and masonry\u003c\/li\u003e\n                \u003cli\u003eANSI specification\u003c\/li\u003e\n                \u003cli\u003eSold individually\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eConcrete\u003c\/li\u003e\n                \u003cli\u003eStone\u003c\/li\u003e\n                \u003cli\u003eBrick\u003c\/li\u003e\n                \u003cli\u003eMasonry\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eSDS-Plus Rotary Hammer\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"ITM","offers":[{"title":"Default Title","offer_id":49639983972590,"sku":"STP-1033","price":23.78,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/itm-stp-sds-plus-stop-drill-bit.jpg?v=1790274150"},{"product_id":"stp-418","title":"7\/8\" SDS-Plus Stop Drill Bit for 5\/8\" Drop-In Anchors","description":"\u003ch2\u003e7\/8\" SDS-Plus Stop Drill Bit for 5\/8\" Drop-In Anchors\u003c\/h2\u003e\n\u003cp\u003eITM\u003c\/p\u003e\n\n\u003cp\u003eA 7\/8\" SDS-Plus hammer bit with a stop lip that bottoms out at 2-5\/8\", the exact hole depth a 5\/8\" drop-in anchor needs. Drill until the lip touches the concrete and the hole is right: the anchor sits flush, the setting tool expands it properly, and the threaded rod pulls against the full cone.\u003c\/p\u003e\n\n\u003cp\u003eOverhead work is where that matters most. Hangers for pipe, duct, sprinkler line, strut and cable tray all land in a concrete deck, and a hole drilled too deep buries the anchor below the surface, while a shallow one stops the anchor short. The stop also keeps you from driving deeper than you need to, which is one less chance of hitting rebar. Carbide tipped, ANSI specification, sold individually.\u003c\/p\u003e\n\n\u003cp\u003eSetting hammer-in anchors on the same job? Use the \u003ca href=\"https:\/\/eldoradotools.com\/products\/sds-hd1\"\u003eSDS-Plus nail-in anchor driver\u003c\/a\u003e. Running a big SDS-Max hammer overhead? The \u003ca href=\"https:\/\/eldoradotools.com\/products\/725max001\"\u003eSDS-Max to SDS-Plus Adapter\u003c\/a\u003e takes these bits without a tool change.\u003c\/p\u003e\n\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eDrill size:\u003c\/strong\u003e 7\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eDrill depth (stop):\u003c\/strong\u003e 2-5\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eFits drop-in anchor:\u003c\/strong\u003e 5\/8\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank:\u003c\/strong\u003e SDS-Plus\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eTip:\u003c\/strong\u003e Carbide tipped\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eStandard:\u003c\/strong\u003e ANSI specification\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eStop lip prevents over-drilling\u003c\/li\u003e\n                \u003cli\u003eDrills the exact depth a drop-in anchor needs\u003c\/li\u003e\n                \u003cli\u003eLess likely to hit rebar\u003c\/li\u003e\n                \u003cli\u003eCarbide tipped for concrete, stone, brick and masonry\u003c\/li\u003e\n                \u003cli\u003eANSI specification\u003c\/li\u003e\n                \u003cli\u003eSold individually\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eConcrete\u003c\/li\u003e\n                \u003cli\u003eStone\u003c\/li\u003e\n                \u003cli\u003eBrick\u003c\/li\u003e\n                \u003cli\u003eMasonry\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eSDS-Plus Rotary Hammer\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"ITM","offers":[{"title":"Default Title","offer_id":49639984234734,"sku":"STP-418","price":30.08,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/itm-stp-sds-plus-stop-drill-bit.jpg?v=1790274150"},{"product_id":"stp-419","title":"1\" SDS-Plus Stop Drill Bit for 3\/4\" Drop-In Anchors","description":"\u003ch2\u003e1\" SDS-Plus Stop Drill Bit for 3\/4\" Drop-In Anchors\u003c\/h2\u003e\n\u003cp\u003eITM\u003c\/p\u003e\n\n\u003cp\u003eA 1\" SDS-Plus hammer bit with a stop lip that bottoms out at 3-1\/4\", the exact hole depth a 3\/4\" drop-in anchor needs. Drill until the lip touches the concrete and the hole is right: the anchor sits flush, the setting tool expands it properly, and the threaded rod pulls against the full cone.\u003c\/p\u003e\n\n\u003cp\u003eOverhead work is where that matters most. Hangers for pipe, duct, sprinkler line, strut and cable tray all land in a concrete deck, and a hole drilled too deep buries the anchor below the surface, while a shallow one stops the anchor short. The stop also keeps you from driving deeper than you need to, which is one less chance of hitting rebar. Carbide tipped, ANSI specification, sold individually.\u003c\/p\u003e\n\n\u003cp\u003eSetting hammer-in anchors on the same job? Use the \u003ca href=\"https:\/\/eldoradotools.com\/products\/sds-hd1\"\u003eSDS-Plus nail-in anchor driver\u003c\/a\u003e. Running a big SDS-Max hammer overhead? The \u003ca href=\"https:\/\/eldoradotools.com\/products\/725max001\"\u003eSDS-Max to SDS-Plus Adapter\u003c\/a\u003e takes these bits without a tool change.\u003c\/p\u003e\n\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eDrill size:\u003c\/strong\u003e 1\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eDrill depth (stop):\u003c\/strong\u003e 3-1\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eFits drop-in anchor:\u003c\/strong\u003e 3\/4\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank:\u003c\/strong\u003e SDS-Plus\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eTip:\u003c\/strong\u003e Carbide tipped\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eStandard:\u003c\/strong\u003e ANSI specification\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eStop lip prevents over-drilling\u003c\/li\u003e\n                \u003cli\u003eDrills the exact depth a drop-in anchor needs\u003c\/li\u003e\n                \u003cli\u003eLess likely to hit rebar\u003c\/li\u003e\n                \u003cli\u003eCarbide tipped for concrete, stone, brick and masonry\u003c\/li\u003e\n                \u003cli\u003eANSI specification\u003c\/li\u003e\n                \u003cli\u003eSold individually\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eConcrete\u003c\/li\u003e\n                \u003cli\u003eStone\u003c\/li\u003e\n                \u003cli\u003eBrick\u003c\/li\u003e\n                \u003cli\u003eMasonry\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eSDS-Plus Rotary Hammer\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"ITM","offers":[{"title":"Default Title","offer_id":49639984300270,"sku":"STP-419","price":35.49,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/itm-stp-sds-plus-stop-drill-bit.jpg?v=1790274150"},{"product_id":"sds-hd1","title":"1\/4\" x 9\" SDS-Plus Nail-In Anchor Driver","description":"\u003ch2\u003e1\/4\" x 9\" SDS-Plus Nail-In Anchor Driver\u003c\/h2\u003e\n\u003cp\u003eITM\u003c\/p\u003e\n\n\u003cp\u003eA spring-loaded SDS-Plus driver that sets 1\/4\" nail-in anchors with the rotary hammer you are already holding. The socket captures the anchor's nail head, the spring holds it square to the surface, and the hammer action drives it home in a second or two, without swinging a hand hammer overhead.\u003c\/p\u003e\n\n\u003cp\u003eNail-in anchors (also called hammer-drive or hammer-set anchors) are the fast way to hang conduit straps, junction boxes, cable clips and light strut on concrete, block and brick. At 9\" long this driver reaches into a deck or a joist space and keeps your knuckles away from the ceiling.\u003c\/p\u003e\n\n\u003cp\u003eDrilling for drop-in anchors as well? The \u003ca href=\"https:\/\/eldoradotools.com\/collections\/sds-plus-anchor-and-concrete-screw-bits\"\u003eSDS-Plus stop drill bits\u003c\/a\u003e drill the exact depth each anchor size needs. On a big machine, the \u003ca href=\"https:\/\/eldoradotools.com\/products\/725max001\"\u003eSDS-Max to SDS-Plus Adapter\u003c\/a\u003e lets this driver run in an SDS-Max hammer.\u003c\/p\u003e\n\n\n\u003cdiv class=\"infomiddle\"\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n                \u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 1\/4\" x 9\"\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eDrives:\u003c\/strong\u003e 1\/4\" nail-in anchors\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eShank:\u003c\/strong\u003e SDS-Plus\u003c\/li\u003e\n                \u003cli\u003e\n\u003cstrong\u003eAction:\u003c\/strong\u003e Rotary hammer, hammer mode\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n                \u003cli\u003eSpring-loaded socket holds the anchor square\u003c\/li\u003e\n                \u003cli\u003eDrives anchors effortlessly with the hammer you already have\u003c\/li\u003e\n                \u003cli\u003e9\" reach for overhead work\u003c\/li\u003e\n                \u003cli\u003eSold individually\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eFor use on:\u003c\/h3\u003e\n                \u003cli\u003eConcrete\u003c\/li\u003e\n                \u003cli\u003eStone\u003c\/li\u003e\n                \u003cli\u003eBrick\u003c\/li\u003e\n                \u003cli\u003eMasonry\u003c\/li\u003e\n        \u003c\/ul\u003e\n        \u003cul id=\"dccheck\"\u003e\n\u003ch3\u003eRuns in:\u003c\/h3\u003e\n                \u003cli\u003eSDS-Plus Rotary Hammer\u003c\/li\u003e\n        \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"ITM","offers":[{"title":"Default Title","offer_id":49639984398574,"sku":"SDS-HD1","price":34.9,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/files\/itm-sds-hd1-nail-in-anchor-driver.jpg?v=1790274150"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0091\/7769\/4268\/collections\/itm-stp-sds-plus-stop-drill-bit.jpg?v=1790274272","url":"https:\/\/eldoradotools.com\/collections\/sds-plus-anchor-and-concrete-screw-bits.oembed","provider":"Eldorado Tools Inc","version":"1.0","type":"link"}