Free shipping over $200 · Supplying commercial contractors across the continental U.S.

Free shipping over $200

Glass Drill Bits: Spear vs Quad vs RAZOR, and How to Drill

HomeBlog & GuidesGuidesGlass & Shower

Glass Drill Bits: Spear vs Quad vs RAZOR, and How to Drill

Glass drill bits, by the hole: Tru-Cut spear point from $3.23 a bit, quad spear to 1 in., and ITM RAZOR at 3 to 4 in. long, plus how ITM says to drill glass.

Tools14 in this guide
Read11 min
UpdatedNov 17, 2026

Quick answer: A glass drill bit is a carbide spear that grinds a hole in glass, mirror or glazed tile. For holes up to 1/2 in., the Tru-Cut spear point is the cheapest bit at every size: the 1/4 in. GD.250 is $4.42 a bit, sold in 25s. The quad spear goes up to 1 in. The ITM RAZOR is the long one, 3 to 4 in. overall. Run all of them with rotation only and water. Never drill tempered glass.

Start with the hole: its size, how many you'll drill, and what sits behind the glass. Those three things pick the bit. Brand comes after.

People call these glass drill bits, spear point bits, spear tip bits, glass and tile bits, glass and mirror bits and carbide glass drills. The quad spear also goes by four-flute or 4-cutter glass bit. Each one is a carbide tip on a steel shank, and it chucks in a standard drill chuck. This guide covers the three styles we sell: Tru-Cut spear point (1/8 to 1/2 in.), Tru-Cut quad spear (3/16 to 1 in.) and ITM RAZOR (1/8 to 1/2 in.). It also covers what ITM, the maker of the RAZOR, says about running them.

What is the difference between a spear point, quad spear and RAZOR glass drill bit?

The three glass drill bits differ in the shape of the carbide tip and in length. A spear point has one flat carbide blade ground to a point, set in a slot across the end of a plain round shank. A quad spear has a cross of carbide at the tip, so it shows four cutting wings end-on. A RAZOR has a spear-shaped carbide tip on a body with spiral flutes behind it, and at 3 to 4 in. it is the longest of the three.

Glass bit Tip, seen end-on Sizes we sell Overall length Price per bit Sold in
Spear point (Tru-Cut GD) One flat blade, two edges 1/8 to 1/2 in. Not published by Tru-Cut $3.23 to $7.80 25s through 5/16 in.; 12s for 3/8 and 1/2 in.
Quad spear (Tru-Cut GDQ) Carbide cross, four edges 3/16 to 1 in. Not published by Tru-Cut $6.14 to $19.63 12s (3/16, 1/4 in.), 6s (5/16 to 3/4 in.), 2s (1 in.)
RAZOR (ITM RAZ) Spear tip on a spiral-fluted body 1/8 to 1/2 in. 3 in. (1/8, 3/16), 4 in. (1/4 to 1/2) $7.13 to $18.56 10s (1/8 to 1/4 in.), then 6, 4 and 2; boxes of 25 in 3/16 and 1/4 in.

Shapes from the Tru-Cut catalog, p. 11, and ITM's 2026 catalog, p. 78. RAZOR lengths from ITM, p. 78. Prices checked on eldoradotools.com on Nov 17, 2026.

No maker we buy from publishes a test showing one tip outlasts or outdrills another, so we don't claim one. Pick by size, length and price per hole.

Which glass drill bit do I need for my hole?

Match the bit to the hole size first. Then pick the style by how many holes you drill and how far the bit has to reach.

  • Holes from 1/8 to 1/2 in., by the box: spear point. It is the lowest price per bit at every size it comes in.
  • Holes from 5/8 to 1 in.: quad spear. It's the only carbide glass bit we sell past 1/2 in.
  • Glass behind a frame, a stack or tile: RAZOR. At 3 to 4 in. overall, it has the most reach of the three.
  • Over 1 in.: we don't carry a carbide glass bit that size. Call us and we'll find one.
  • Porcelain tile: a glass bit isn't the tool. Use a V-Groove porcelain bit.

Here is every glass drill bit we sell, by hole size. The price is per bit. The minimum is what the store adds to your cart.

Size Style Part Price per bit Minimum order Cost of the minimum
1/8 in. Spear point GD.125 $3.23 25 $80.75
1/8 in. RAZOR, 3 in. RAZ-4001 $7.13 10 $71.30
5/32 in. Spear point GD.156 $3.37 25 $84.25
3/16 in. Spear point GD.187 $3.54 25 $88.50
3/16 in. Quad spear GDQ.187 $6.14 12 $73.68
3/16 in. RAZOR, 3 in. RAZ-4002 $7.74 10 $77.40
3/16 in. RAZOR, 3 in., box of 25 RAZ-4002B $7.29 1 box $182.17
1/4 in. Spear point GD.250 $4.42 25 $110.50
1/4 in. Quad spear GDQ.250 $7.47 12 $89.64
1/4 in. RAZOR, 4 in. RAZ-4003 $8.39 10 $83.90
1/4 in. RAZOR, 4 in., box of 25 RAZ-4003B $7.90 1 box $197.41
5/16 in. Spear point GD.312 $4.74 25 $118.50
5/16 in. Quad spear GDQ.312 $8.08 6 $48.48
5/16 in. RAZOR, 4 in. RAZ-4004 $10.20 6 $61.20
3/8 in. Spear point GD.375 $6.38 12 $76.56
3/8 in. Quad spear GDQ.375 $9.47 6 $56.82
3/8 in. RAZOR, 4 in. RAZ-4005 $14.41 4 $57.64
1/2 in. Spear point GD.500 $7.80 12 $93.60
1/2 in. Quad spear GDQ.500 $11.24 6 $67.44
1/2 in. RAZOR, 4 in. RAZ-4006 $18.56 2 $37.12
5/8 in. Quad spear GDQ.625 $13.32 6 $79.92
3/4 in. Quad spear GDQ.750 $14.81 6 $88.86
1 in. Quad spear GDQ1.000 $19.63 2 $39.26

Prices checked on eldoradotools.com on Nov 17, 2026. The 5/8 and 3/4 in. quads have a 3/8 in. shank. ITM lists the RAZOR shanks as 1/8, 3/16, 1/4, 1/4, 5/16 and 3/8 in., smallest to largest.

Only a few holes to drill? Look at the last column. The smallest buy-ins are the 1/2 in. RAZOR (RAZ-4006, 2 bits for $37.12) and the 1 in. quad (GDQ1.000, 2 bits for $39.26).

Is a box of glass drill bits worth it?

A box of glass drill bits pays off when you drill glass every week. The spear point costs the least per bit at every size up to 1/2 in. Each size up raises the price per bit, and the gap between styles widens: at 1/2 in., a RAZOR costs more than twice a spear point.

Bit diameter (in.) Spear point Quad spear RAZOR
1/8 $3.23 — $7.13
5/32 $3.37 — —
3/16 $3.54 $6.14 $7.74
1/4 $4.42 $7.47 $8.39
5/16 $4.74 $8.08 $10.20
3/8 $6.38 $9.47 $14.41
1/2 $7.80 $11.24 $18.56
5/8 — $13.32 —
3/4 — $14.81 —
1 — $19.63 —

How to read this chart: each line is one style of glass drill bit. Find your hole size along the bottom, then read the price of one bit up the side.

Takeaway: up to 1/2 in., the spear point is the cheapest bit at every size. Past 1/2 in., only the quad spear goes.

Price per bit at the store minimum, checked on eldoradotools.com on Nov 17, 2026. The RAZOR box of 25 brings 3/16 in. to $7.29 a bit and 1/4 in. to $7.90.

Our trade accounts buy two sizes. Of the 3,657 spear-point glass bits they bought from us in the 12 months to Nov 17, 2026, 3,620 were 3/16 or 1/4 in.: 2,890 of the 1/4 in. GD.250 and 730 of the 3/16 in. GD.187. Check your hardware's sheet for the hole size before you order.

"Almost every glass bit we ship is a 3/16 or a 1/4, and the shops buy them by the box. Nobody stops a job to go hunt for a bit. You reach in the box and grab the next one."

— David Castro, Eldorado Tools

How do you drill a hole in glass without cracking it?

To drill a hole in glass without cracking it, run a carbide glass drill bit with rotation only, keep the hole wet, and let the tip grind instead of pushing it. ITM, which makes the RAZOR, prints three rules on its glass drill page: rotation only, use water, and "fast drilling speeds and lubricant are recommended." Its icons show a drill that chucks up to 1/2 in.

  1. Make sure the glass isn't tempered. If you can't confirm it, don't drill it. Tempered glass breaks apart when drilled.
  2. Lay it flat and support it. The glass should sit fully on a flat, solid surface with no part hanging over the edge.
  3. Start the hole. A suction drill guide holds the tip on slick glass. The GUIDE-1 is for holes from 5/32 to 7/16 in., and GUIDE-2 for 5/32 to 3-1/4 in. Hold the guide until the bit is about 1/8 in. into the surface, then you can lift it off.
  4. Turn hammer off. ITM marks its glass drills rotation only.
  5. Keep the tip wet. Water or cutting lubricant at the tip the whole time, per ITM.
  6. Set the speed the bit's maker gives. ITM says fast speeds for its glass drills. Drill America says slow speeds for its 4-flute glass and tile bits. Neither prints an RPM, so neither do we. Follow the maker of the bit in your chuck.
  7. Feed lightly, and ease off at the end. Let the carbide do the cutting. Back off the pressure as the tip comes through the far side.

For drilling the tile behind a shower door, see frameless shower door installation. For tile and porcelain, see how to drill through tile.

Can you drill tempered glass?

No, you can't drill tempered glass. Any hole or notch in tempered glass is made before the glass is tempered. ITM's own video, "Don't Drill Tempered Glass!", shows a tempered pane exploding when it's drilled. If a shower door, a glass shelf or a tabletop needs a new hole, order a new panel with the hole made.

How close to the edge can you drill a hole in glass?

None of the bit makers we buy from publishes an edge distance for glass. Viracon, a glass fabricator, publishes its own minimums for holes in the glass it makes. Its edge rule is at least 1/4 in. or 2 times the glass thickness, whichever is greater, measured from the edge of the hole. From a corner it wants 6.5 times the thickness, and between two holes, 2 times the thickness or 10 mm. On 1/4 in. glass, that puts a hole at least 1/2 in. from the edge. If your glass came from a fabricator, use its numbers.

When should you use a diamond bit for glass instead?

A diamond core bit is for holes bigger than a carbide glass drill bit goes, and for porcelain. Our carbide glass bits stop at 1 in. (GDQ1.000). For a larger hole in glass, call us and we'll find the right core. For porcelain tile, which glass bits aren't rated for, use a V-Groove porcelain bit or a diamond core. Our shower valve hole size guide lists the cores by size.

Glass drill bit FAQ

Can I use a cordless drill to drill glass?

Yes. Any drill with rotation only and a chuck that takes the shank works. ITM marks its glass drills for a drill with a 1/2 in. chuck. Turn the hammer setting off.

Will a glass drill bit go through mirror?

Yes. ITM lists its glass drills for glass, mirror, ceramic and plastics. Keep the hole wet and feed lightly.

Will a glass drill bit go through porcelain tile?

Porcelain isn't on ITM's list for its glass drills. Use a V-Groove porcelain bit instead.

Why does my glass bit skate across the glass?

Smooth glass gives the point nothing to bite. Hold a suction guide such as GUIDE-1 over the mark until the bit is about 1/8 in. in.

Why does the back of the hole chip?

Usually from too much pressure as the tip comes through, or glass that isn't fully supported. Ease off at the end and keep the glass flat on a solid surface.

What's the difference between a glass drill bit and a tile bit?

A glass drill bit has a spear-shaped carbide tip and is made to grind. A porcelain tile bit such as V-Groove has a different carbide head. ITM lists its glass drills for ceramic as well as glass.

Is the RAZOR the same as an ITM spear point?

No. ITM sells both. The RAZOR has a spear tip on a spiral-fluted body and runs 3 to 4 in. long. ITM's standard glass drill has a plain shank. We stock the RAZOR from ITM and the spear point from Tru-Cut.

Do you sell a glass drill bit set?

Yes, two quad spear sets: GDQ.SET (1/4, 5/16, 3/8 and 1/2 in., $32.50 a set) and GDQ.SET2 (3/16, 1/4, 5/16 and 3/8 in., $27.75 a set). Both are sold two sets at a time.

Not sure which size your hardware needs? Call our team at (833) 4-ETOOLS or email sales@eldoradotools.com with the hardware and the glass thickness, and we'll name the part.

Related: all glass drill bits, frameless shower door installation, how to drill through tile, drill bits for porcelain tile and types of drill bits.

Sources: ITM 2026 catalog, p. 78 (RAZOR sizes, lengths and shanks; glass drill shapes; rotation only, water, "fast drilling speeds and lubricant"; glass, ceramic, mirror and plastics); Tru-Cut catalog, p. 11 (spear and quad sizes and shapes); ITM video "Don't Drill Tempered Glass!"; Drill America video "4 Flute Glass and Tile Drill Bits" (slow speed); Viracon, "Holes" (edge, corner and spacing minimums). Prices and minimums from eldoradotools.com, and sales from our order records, on Nov 17, 2026.

First published Nov 17, 2026, with prices checked on Nov 17, 2026.

← Back to Blog & Guides
Vanessa Franchesca
Written by Vanessa Franchesca

Vanessa Franchesca is a highly skilled professional with a passion for policy, marketing, and digital strategy. With a proven track record of success, she has excelled in developing and implementing effective campaigns. Vanessa's expertise lies in policy development, social media management, content creation, and brand development. Her strong analytical skills and creativity allow her to deliver impactful results for her clients. With a Bachelor's degree in Social Sciences from Harvard University’s Extension School with a concentration in Government, and years of experience in the industry, Vanessa is dedicated to driving growth and helping businesses and people thrive in the digital landscape. Connect with her on LinkedIn to explore new opportunities and stay updated on the latest marketing trends.