Free shipping over $200 · Supplying commercial contractors across the continental U.S.

Free shipping over $200

SDS Plus Rebar Cutter Sizes vs SDS-Max and Straight Shank

HomeBlog & GuidesGuidesFoundation & Basement Repair

SDS Plus Rebar Cutter Sizes vs SDS-Max and Straight Shank

Match the rebar cutter to the machine on the job: SDS-Plus cutters, SDS-Max punchers and straight-shank cutters, with every size, speed and price.

Tools12 in this guide
Read14 min
UpdatedNov 18, 2026

Quick answer: The machine in your hands picks the shank, the hole picks the size, and the bar picks cutter or puncher. On an SDS-Plus rotary hammer, buy the SDS Plus rebar cutter the size of your bit, such as the 5/8 in. RBS-10 ($53.90), and run it with the hammer off. On an SDS-Max hammer there is no rotation-only cutter; the 5/8 to 1-3/4 in. RMX puncher stays in hammer mode. With a 1/2 in. chuck drill, the straight-shank cutter is the cheapest at every size.

You are drilling an anchor or dowel hole and the bit stops dead on steel. Now you need a tool that cuts the bar, and it has to fit the machine that is already on the job. This guide sorts every rebar cutter and rebar puncher we sell by that machine first, then by hole size and bar size.

The trade has a lot of names for these. A rebar cutter is also called a rebar cutter bit, rebar cutting bit, rebar drill bit, rotary rebar cutter or rebar eater. A rebar puncher is a different tool: it runs with the hammer on. Every part below is made by ITM, sold one per tube, and priced per piece.

Which rebar cutter fits my drill or rotary hammer?

A rebar cutter fits your machine by its shank: an SDS Plus rebar cutter for an SDS-Plus rotary hammer, a straight shank for any drill with a 1/2 in. chuck, and for an SDS-Max hammer, a puncher, because nobody we buy from makes a rotation-only cutter with an SDS-Max shank.

Machine on the job What to buy Hammer setting Sizes we sell Example and price
SDS-Plus rotary hammer SDS-Plus rebar cutter Off (rotation only) 3/8 to 1-1/2 in. RBS-10, 5/8 x 12 in., $53.90
SDS-Plus rotary hammer, bar every few holes SDS-Plus rebar puncher (#5 bar and lighter) On 3/8 to 1-1/4 in., 12 or 18 in. long RT-10, 5/8 x 12 in., $83.42
SDS-Max rotary hammer SDS-Max rebar puncher (#5 bar and lighter) On 5/8 to 1-3/4 in., 12 or 21 in. long RMX-16, 1 x 12 in., $180.98
Drill with a 1/2 in. chuck Straight-shank rebar cutter Off (rotation only) 3/8 to 2-1/2 in. RBC1258, 5/8 x 12 in., $48.08

Sizes and modes from ITM's 2026 catalog, pp. 100–101. Prices checked on eldoradotools.com on Nov 18, 2026.

The straight shank is the one that frees up your rotary hammer. One person keeps drilling holes while a second person cuts bar with a regular drill. ITM marks the straight-shank cutters for a 1/2 in. drill.

"Buy the cutter for the hammer that's already on the job. If your crew runs SDS-Max, the puncher keeps that hammer working. If the bar is #6 or heavier, put a straight-shank cutter in a regular drill and let the hammer keep drilling."

David Castro, President, Eldorado Tools

What size rebar cutter do I need?

Buy the SDS Plus rebar cutter or straight-shank cutter the same size as the bit you are drilling with, not the size of the bar. ITM's method is to stop at the bar, put the cutter into the hole you already drilled, cut through the steel, then finish with your hammer bit. So a 5/8 in. anchor hole that runs into #4 bar takes a 5/8 in. cutter.

Speed matters as much as size. ITM gives each size its own speed, and the bigger the cutter, the slower it runs. The speeds are the same for the SDS-Plus and straight-shank cutters.

Hole size Cutter speed, hammer off (RPM) SDS-Plus rebar cutter Straight-shank rebar cutter (1/2 in. chuck) SDS-Plus rebar puncher SDS-Max rebar puncher
3/8 in. 850 to 1,200 RBS-6 (8 in.), $40.61 RBC0838 (8 in.), $34.05 RT-6, $48.36 –
1/2 in. 850 to 1,200 RBS-8, $42.50 RBC1212, $40.45 RT-8, $74.75 –
9/16 in. 850 to 1,200 RBS-9, $44.41 RBC1916, $41.87 – –
5/8 in. 750 to 1,000 RBS-10, $53.90 RBC1258, $48.08 RT-10, $83.42 RMX-10, $145.88
11/16 in. 750 to 1,000 RBS-11, $57.69 RBC1116, $51.53 – –
3/4 in. 600 to 850 RBS-12, $59.58 RBC1234, $54.62 RT-12, $92.49 RMX-12, $170.01
13/16 in. 600 to 850 RBS-13, $72.88 RBC1316, $64.30 – –
7/8 in. 600 to 850 RBS-14, $84.39 RBC1278, $75.65 RT-14, $94.29 RMX-14, $175.49
1 in. 500 to 750 RBS-16, $89.95 RBC1201, $81.32 RT-16, $97.03 RMX-16, $180.98
1-1/8 in. 500 to 750 RBS-18, $95.64 RBC1218, $87.01 RT-18, $123.95 RMX-18, $186.46
1-1/4 in. 450 to 600 RBS-20, $101.33 RBC1214, $92.68 RT-20, $132.63 RMX-20, $195.46
1-3/8 in. 450 to 600 RBS-22, $110.83 RBC1238, $102.14 – RMX-22, $220.57
1-1/2 in. 350 to 500 RBS-24, $116.51 RBC1112, $108.95 – RMX-24, $263.24
1-3/4 in. 350 to 500 – RBC1134, $140.61 – RMX-26, $283.09
2 in. 350 to 500 – RBC1202, $211.83 – –
2-1/2 in. 350 to 500 – RBC1222, $249.66 – –

Speeds, sizes and lengths from ITM's 2026 catalog, p. 100 (cutters) and p. 101 (punchers). Lengths are 12 in. unless marked. ITM gives no speed for punchers; they run in hammer mode. Prices checked on eldoradotools.com on Nov 18, 2026, per piece.

Here is the same lineup by price. A straight-shank cutter is the lowest price at every size. An SDS-Max puncher costs two to three times as much as a straight-shank cutter of the same size, but it never leaves the big hammer.

Hole size (in.) Straight-shank cutter ($) SDS-Plus cutter ($) SDS-Plus puncher ($) SDS-Max puncher ($)
3/8 in. $34.05 $40.61 $48.36 –
1/2 in. $40.45 $42.50 $74.75 –
9/16 in. $41.87 $44.41 – –
5/8 in. $48.08 $53.90 $83.42 $145.88
11/16 in. $51.53 $57.69 – –
3/4 in. $54.62 $59.58 $92.49 $170.01
13/16 in. $64.30 $72.88 – –
7/8 in. $75.65 $84.39 $94.29 $175.49
1 in. $81.32 $89.95 $97.03 $180.98
1-1/8 in. $87.01 $95.64 $123.95 $186.46
1-1/4 in. $92.68 $101.33 $132.63 $195.46
1-3/8 in. $102.14 $110.83 – $220.57
1-1/2 in. $108.95 $116.51 – $263.24
1-3/4 in. $140.61 – – $283.09
2 in. $211.83 – – –
2-1/2 in. $249.66 – – –

How to read this chart: find your hole size along the bottom; each line is one kind of tool, and its height is the price of one 12 in. part (the 3/8 in. cutters are 8 in.). What it means for you: if a second person can run a drill, a straight-shank cutter is the cheapest way through the bar at every size.

Is there an SDS-Max rebar cutter?

No maker we buy from sells a rotation-only rebar cutter with an SDS-Max shank. ITM's only SDS-Max rebar tool is the RMX rebar puncher, and it runs in hammer mode. That is good news if you drill with an SDS-Max hammer: you punch the bar with the same machine, with no mode change and no second tool.

  • Bar #5 (5/8 in.) or lighter: use the SDS-Max puncher the size of your hole, 5/8 to 1-3/4 in. For example, RMX-16 for a 1 in. hole ($180.98). ITM rates it "best on #5 (5/8") rebar size and under".
  • Bar #6 or heavier: cut it with a straight-shank cutter in a 1/2 in. chuck drill, such as RBC1201 for a 1 in. hole ($81.32).
  • Holes under 5/8 in.: there is no SDS-Max puncher that small. Use a straight-shank cutter in a drill.
  • Holes over 1-3/4 in.: only the straight-shank cutters go bigger, to 2 and 2-1/2 in., such as RBC1222 for 2-1/2 in. ($249.66).

Some crews put an SDS-Plus cutter in the big hammer with an SDS-Max to SDS-Plus adapter (725MAX001, $75.16). That only works if your SDS-Max hammer has a rotation-only setting, because a cutter must never run with the hammer on. Check the switch before you buy.

Rebar cutter or rebar puncher: which one for my bar?

A rebar cutter works on any bar, but only with the hammer off. A rebar puncher keeps the hammer on, and ITM rates it best on #5 (5/8 in.) bar and under, so heavier bar calls for the cutter.

Rebar cutter Rebar puncher
Hammer setting Off. ITM: "Rotation Only!" On. ITM: "Use in rotary hammer mode"
Bar size Any Best on #5 (5/8 in.) and under, per ITM
Speed ITM's speed for its size, 350 to 1,200 RPM ITM rates it at "twice the speed"
Shanks SDS-Plus, straight SDS-Plus, SDS-Max
Price, 3/4 in. x 12 in. RBC1234 ($54.62) straight; RBS-12 ($59.58) SDS-Plus RT-12 ($92.49) SDS-Plus; RMX-12 ($170.01) SDS-Max
Pick it when You hit bar now and then, or the bar is #6 and up You hit light bar every few holes and don't want to switch modes

Not sure what bar is in the slab? The drawings name it. Here are the common sizes. A bar's ribs make it fatter than its name, which is one more reason to size the cutter to your hole, not the bar.

Bar Nominal diameter Diameter over the ribs Puncher rated for it?
#3 3/8 in. (0.375) 0.44 in. Yes
#4 1/2 in. (0.500) 0.56 in. Yes
#5 5/8 in. (0.625) 0.69 in. Yes
#6 3/4 in. (0.750) 0.88 in. No, use a cutter
#7 7/8 in. (0.875) 1.00 in. No, use a cutter
#8 1 in. (1.000) 1.13 in. No, use a cutter

Nominal diameters per ASTM A615; diameters over the ribs from Caltrans Bridge Design Details 13.1, Table 13.1.1. Puncher rating from ITM's 2026 catalog, p. 101.

How many holes does a rebar cutter last?

A rebar cutter is a problem solver, not a long-life bit. ITM says a 1/2 in. cutter that meets #6 bar dead center "may result in 5 to 10 holes" at the right speed and pressure. ITM also warns that "it is not uncommon for only one piece of rebar to be cut per Rebar Cutter." ITM cutters "are not warrantied for replacement or repair."

So plan on two in the size you drill most. A second cutter in the truck costs less than sending someone off the job to find one. Three things kill a cutter early:

  • The hammer left on. Hammering shatters the carbide teeth on the bar.
  • Drilling concrete with it. ITM: rebar cutters "should not be used for drilling concrete." Drill to the bar with your concrete bit, then switch.
  • Running too fast. Use the speed for the size in the table above. A 2 in. cutter runs at 350 to 500 RPM, not the 1,200 a small one can take.

For the full step-by-step, including the 4-cutter bits that drill past glancing hits, see our guide on how to drill through rebar.

How deep can a rebar cutter reach?

Most of these parts are 12 in. long. For bar deeper in the wall or footing, the SDS-Plus punchers also come 18 in. long, the SDS-Max punchers 21 in., and the 3/4 in. straight-shank cutter 18 in. ITM doesn't publish a working depth, so measure from the face of the concrete to the bar and leave room for the chuck.

Hole size SDS-Plus puncher, 18 in. SDS-Max puncher, 21 in. Straight-shank cutter, 18 in.
3/8 in. RT-6-18, $69.09 – –
1/2 in. RT-8-18, $95.69 – –
5/8 in. RT-10-18, $93.66 RMX-10-21, $175.49 –
3/4 in. RT-12-18, $101.79 RMX-12-21, $180.98 RBC1834, $69.98
7/8 in. RT-14-18, $103.76 RMX-14-21, $186.46 –
1 in. RT-16-18, $134.78 RMX-16-21, $191.95 –
1-1/8 in. RT-18-18, $138.83 RMX-18-21, $197.43 –
1-1/4 in. RT-20-18, $146.20 RMX-20-21, $206.42 –
1-3/8 in. – RMX-22-21, $231.54 –
1-1/2 in. – RMX-24-21, $274.21 –
1-3/4 in. – RMX-26-21, $294.06 –

Lengths from ITM's 2026 catalog, pp. 100–101. Prices checked on eldoradotools.com on Nov 18, 2026, per piece. The 18 and 21 in. punchers carry the same "#5 and under" rating.

There is no SDS-Plus rebar cutter longer than 12 in. If the bar is deeper than that and heavier than #5, the only long cutter we sell is the 3/4 in. RBC1834 ($69.98). Call us for other sizes.

Which rebar cutter should a data center crew carry?

A data center crew should carry an SDS Plus rebar cutter sized to its most common anchor hole, plus a straight-shank cutter for a second drill. Every bar hit stops a rotary hammer, and on an anchor-heavy job those stops add up.

Start from the anchor. A standard drop-in anchor takes a bit one size up from its rod, so the cutter follows the bit. These sizes come from our drop-in anchor drill bit guide, which checked each one against the anchor makers' sheets.

Rod size (standard drop-in) Bit SDS-Plus cutter Straight-shank cutter
3/8 in. 1/2 in. RBS-8 ($42.50) RBC1212 ($40.45)
1/2 in. 5/8 in. RBS-10 ($53.90) RBC1258 ($48.08)
5/8 in. 7/8 in. RBS-14 ($84.39) RBC1278 ($75.65)
3/4 in. 1 in. RBS-16 ($89.95) RBC1201 ($81.32)
3/8 in. Hilti HDI-TZ 9/16 in. RBS-9 ($44.41) RBC1916 ($41.87)

Bit sizes from Simpson Strong-Tie, Hilti, DeWalt and Red Head drop-in sheets, as listed in our drop-in anchor guide (Hilti 3/8 in. HDI-TZ per ICC-ES ESR-4236). Prices checked on eldoradotools.com on Nov 18, 2026.

Before anyone cuts, get the engineer's answer. Hilti's engineering team says that if reinforcement is hit, the installer should check with the responsible engineer, and if the engineer does not approve drilling through it, the anchor should be moved. If the deck is post-tensioned, a tendon is not rebar. Scan first, and cut only what the engineer approves.

Every part in this guide is in our data center slab, rebar and demo collection. The anchors themselves go in with the bits in hangers and tray anchors and rack and equipment anchors, and our data center page lays out every job step.

Which rebar cutter should a foundation repair crew carry?

A foundation repair crew drilling with an SDS-Max hammer should carry an SDS-Max puncher in its main hole size and one straight-shank cutter for heavy bar. Wall anchor and pier holes run big and deep, and the puncher keeps the big hammer working.

  • Deep footing or wall holes on light bar: the 21 in. SDS-Max puncher in your hole size, such as RMX-18-21 ($197.43) for 1-1/8 in.
  • #6 and heavier bar: a straight-shank cutter the same size in a 1/2 in. chuck drill, such as RBC1218 ($87.01) for 1-1/8 in.
  • Reaching farther: for the hole itself, our SDS Max drill bits guide lists every length.

Shop the whole lineup in foundation repair rebar cutting, or by shank: SDS-Plus, SDS-Max and straight shank.

Rebar cutter FAQ

Can I use a rebar cutter in hammer mode?

No. ITM marks its rebar cutters "Rotation Only!", and hammering breaks the carbide teeth. If you want to keep the hammer on, use a rebar puncher on #5 bar and lighter.

Does a rebar cutter drill concrete?

No. ITM says rebar cutters should not be used for drilling concrete. Drill to the bar with a concrete bit, cut the bar, then switch back.

What RPM should I run a rebar cutter at?

It depends on the size. ITM gives 850 to 1,200 RPM for 3/8 to 9/16 in. cutters, down to 350 to 500 RPM for 1-1/2 in. and bigger. The size table above lists every size.

Is there an SDS-Max rebar cutter?

Not a rotation-only one from any maker we buy from. On an SDS-Max hammer, use the RMX rebar puncher (5/8 to 1-3/4 in.) on #5 bar and lighter, and a straight-shank cutter in a drill for heavier bar.

Why did my rebar cutter only cut one bar?

ITM says that is "not uncommon." Hitting heavy bar dead center, too much speed and too much pressure all shorten its life. Keep a second cutter in your most common size.

Will an SDS Plus rebar cutter fit an SDS-Max hammer?

Only with an SDS-Max to SDS-Plus adapter such as 725MAX001, and only if the hammer has a rotation-only setting.

Not sure which part fits your machine? Call our team at (833) 4-ETOOLS or email sales@eldoradotools.com with the machine, the hole size and the bar size, and we'll name the part.

Related: all rebar cutters, rebar drill bits and how to drill through rebar, SDS Plus vs SDS Max and drop-in anchor drill bits.

Sources: ITM 2026 catalog, p. 100 (rebar cutter sizes, lengths and speeds; "Rotation Only!"; 3 steps to drilling rebar; life, concrete and warranty notes) and p. 101 (rebar puncher sizes and lengths; hammer mode; "Twice the Speed"; "best on #5 (5/8") rebar size and under"); ASTM A615 nominal bar diameters; Caltrans Bridge Design Details 13.1, Table 13.1.1 (diameters over the ribs); Hilti Engineering Q&A on hitting reinforcement; anchor makers' drop-in sheets as cited in our drop-in anchor guide. Prices from eldoradotools.com on Nov 18, 2026.

← Back to Blog & Guides
Vanessa Franchesca
Written by Vanessa Franchesca

Vanessa Franchesca is a highly skilled professional with a passion for policy, marketing, and digital strategy. With a proven track record of success, she has excelled in developing and implementing effective campaigns. Vanessa's expertise lies in policy development, social media management, content creation, and brand development. Her strong analytical skills and creativity allow her to deliver impactful results for her clients. With a Bachelor's degree in Social Sciences from Harvard University’s Extension School with a concentration in Government, and years of experience in the industry, Vanessa is dedicated to driving growth and helping businesses and people thrive in the digital landscape. Connect with her on LinkedIn to explore new opportunities and stay updated on the latest marketing trends.