HomeBlog & GuidesGuidesElectrical
Drill Tap Bits: Which Size for Panels, Boxes and Sheet Metal
How thick each drill tap size can go, whether the threads hold in sheet steel, which size fits which job, and what it costs to start versus a drill and tap.
Quick answer: A drill tap drills, threads and chamfers a through hole in one pass, straight from a 1/4 in. hex driver. It's a thin-metal tool: boxes, enclosures, back panels, rack rails, brackets and light plate. For the usual 10-32 ground screw in a steel box, the ITM HDT-1032 does it ($15.71 each, sold in 4s). If the metal is thicker than the bit's short thread section, or the hole is blind, drill and tap it the two-step way.
Most tapped holes on a service call aren't machining. They're a ground screw in a box that came without a tapped hole, a DIN rail on a back panel, a bracket on a rooftop stand. You need a clean thread in a minute, from the driver already in your hand, without a tap wrench and a separate drill.
That's the job a drill tap was built for. It's also sold as a combination drill tap, a drill/tap bit or a drill and tap bit; Greenlee, Klein, Milwaukee and DeWalt all make one. This guide covers how thick each size can go, whether the threads will actually hold in sheet steel, which size fits which job, and what it costs to get started. The bits here are ITM HD combination drill taps: M2 high-speed steel with a ground thread and a 1/4 in. hex impact shank.
What is a drill tap, and when does it beat a drill and a tap?
A drill tap is one bit with three cutting sections. The tip is a drill that makes the hole, the middle is a tap that cuts the thread, and a chamfer behind the thread breaks the edge so the screw starts clean. ITM's catalog shows it in three steps: drilling, tapping, chamfer. Because the drill tip runs ahead of the thread, a drill tap only finishes holes that go all the way through.
| Your hole | Drill tap | Separate drill + tap |
|---|---|---|
| Through sheet, a box wall or a panel | Best: one pass, chamfered | Works, three tool changes |
| Through plate thicker than the bit's thread section | No | Yes |
| Blind hole (stops inside the part) | No: the drill tip runs past the thread | Yes: plug tap, then a bottoming tap |
| Dozens of holes, one size, at a bench | Works | Cheaper per hole |
| Fine or metric thread we don't carry as a drill tap (1/4-28, M6) | No | Yes |
For blind holes and the two-step method, see how to use a tap and die set. For the drill that goes with each tap, use the tap drill size chart.
How thick can a drill tap go?
A drill tap is made for sheet and light plate. Its thread section is short, from 9/64 in. on a 6-32 to 15/32 in. on a 3/8-16. ITM prints that thread length for every size. It doesn't print a maximum material thickness, a speed, or a rating for stainless steel.
So here's the rule we use: if the wall is thicker than the bit's thread section, drill and tap it the two-step way. Inside that limit, the drill tap cuts the full wall in one pass.
| Thread | Drill tap | Thread length (ITM) | Overall length (ITM) | Price each | Sold in |
|---|---|---|---|---|---|
| 6-32 | HDT-0632 | 9/64 in. | 2-1/4 in. | $14.83 | 4 |
| 8-32 | HDT-0832 | 5/32 in. | 2-1/4 in. | $15.20 | 4 |
| 10-24 | HDT-1024 | 13/64 in. | 2-1/4 in. | $15.71 | 4 |
| 10-32 | HDT-1032 | 5/32 in. | 2-23/64 in. | $15.71 | 4 |
| 12-24 | HDT-1224 | 13/64 in. | 2-23/64 in. | $16.52 | 4 |
| 1/4-20 | HDT-1420 | 1/4 in. | 2-37/64 in. | $18.36 | 2 |
| 5/16-18 | HDT-5618 | 29/64 in. | 3 in. | $25.67 | 2 |
| 3/8-16 | HDT-3816 | 15/32 in. | 3-3/16 in. | $25.67 | 2 |
| 1/2-13 | HDT-1213 | 27/64 in. | 3-13/32 in. | $36.03 | 1 (single) |
Thread length and overall length from the ITM 2026 catalog, p. 35. Prices from eldoradotools.com on Nov 19, 2026. "Sold in" is the order minimum; you pay the per-piece price for each.
Other makers print a capacity for their own bits: Milwaukee and DeWalt rate their 1/4-20 drill taps for metal up to 1/4 in. thick, and Klein rates its 1/4-20 for up to 10 gauge. Those numbers belong to those bits. ITM hasn't published one for the HD line, and we won't guess at it. If you have a thickness that's close, call us before you order.
Will the threads hold in thin sheet metal?
That depends on how many threads fit in the wall. Multiply the thickness by the threads per inch: 14 gauge steel is 0.0747 in., so a 10-32 gets 0.0747 × 32 = 2.4 threads. A 10-24 in the same wall gets 1.8. The finer the thread, the more of it fits in thin metal.
UL 50, the standard for electrical enclosures, says metal that takes a screw must give at least two full threads of engagement, and it lists the thinnest steel it accepts for each thread pitch (bottom row below). That's why 10-32 is the ground screw: UL accepts a 32-thread screw in steel 0.053 in. thick, which covers a 16 gauge box. A 10-24 needs 0.080 in., which is 12 gauge.
| Steel thickness | 6-32, 8-32, 10-32 | 10-24, 12-24 | 1/4-20 | 5/16-18 | 3/8-16 | 1/2-13 |
|---|---|---|---|---|---|---|
| 18 ga (0.0478 in.) | 1.5 (thin) | 1.1 (thin) | 1.0 (thin) | 0.9 (thin) | 0.8 (thin) | 0.6 (thin) |
| 16 ga (0.0598 in.) | 1.9 | 1.4 (thin) | 1.2 (thin) | 1.1 (thin) | 1.0 (thin) | 0.8 (thin) |
| 14 ga (0.0747 in.) | 2.4 | 1.8 (thin) | 1.5 (thin) | 1.3 (thin) | 1.2 (thin) | 1.0 (thin) |
| 12 ga (0.1046 in.) | 3.3 | 2.5 | 2.1 | 1.9 (thin) | 1.7 (thin) | 1.4 (thin) |
| 11 ga (0.1196 in.) | 3.8 | 2.9 | 2.4 | 2.2 | 1.9 (thin) | 1.6 (thin) |
| 10 ga (0.1345 in.) | 4.3 | 3.2 | 2.7 | 2.4 | 2.2 | 1.7 (thin) |
| 3/16 in. (0.1875 in.) | 6.0 | 4.5 | 3.8 | 3.4 | 3.0 | 2.4 |
| 1/4 in. (0.2500 in.) | 8.0 | 6.0 | 5.0 | 4.5 | 4.0 | 3.2 |
| 3/8 in. (0.3750 in.) | 12.0 | 9.0 | 7.5 | 6.8 | 6.0 | 4.9 |
| UL 50 minimum steel | 0.053 in. | 0.080 in. | 0.093 in. | 0.108 in. | 0.123 in. | Not listed |
Threads = thickness × threads per inch. Sheet thickness is the standard steel gauge (plain steel). Minimums from UL 50 (13th edition), section 6.1.8; UL lists no minimum for 13 threads per inch, so for 1/2-13 we mark under two threads as thin.
What it means for you: in a 16 gauge box or cover, tap 10-32 and nothing coarser. 1/4-20 needs 12 gauge, 5/16-18 needs 11 gauge and 3/8-16 needs 10 gauge; in anything thinner, those threads will cut but strip, so put a nut on the back instead.
Ground screws in boxes and enclosures
The NEC lets a machine screw bond equipment to a box when it engages at least two threads or is held with a nut (NEC 250.8(A)). RACO taps most of its steel boxes with a #10-32 grounding hole, and its boxes are 0.0625 in. steel, which is exactly two threads of 10-32. When a box or enclosure has no ground hole, scrape the paint off the spot, center punch it, and run the HDT-1032 through. In covers thinner than 16 gauge, skip the tap and use a nut.
Which drill tap do I need for my job?
Match the bit to the screw, then check the wall against the table above.
| Job | Usual thread | Drill tap | First order |
|---|---|---|---|
| Ground screw in a steel box, enclosure or panel | 10-32 | HDT-1032 | 4 × $15.71 = $62.84 |
| DIN rail, terminal blocks or devices on an enclosure back panel | 10-32 or 1/4-20 | HDT-1032 or HDT-1420 | $62.84 or $36.72 |
| Cover screws and small devices | 6-32 or 8-32 | HDT-0632 or HDT-0832 | $59.32 or $60.80 |
| Extra or stripped holes in a threaded rack rail | 12-24 or 10-32 | HDT-1224 or HDT-1032 | $66.08 or $62.84 |
| Disconnect, controller or equipment brackets on an HVAC stand or rail | 1/4-20 or 5/16-18 | HDT-1420 or HDT-5618 | $36.72 or $51.34 |
| Angle, brackets and base plates you bolt to strut | 3/8-16 or 1/2-13 | HDT-3816 or HDT-1213 | $51.34 or $36.03 |
Prices from eldoradotools.com on Nov 19, 2026, at our order minimums. Check the rack maker's sheet before you tap: Panduit's R2P rack, for one, uses #12-24 rails in aluminum, and ITM lists aluminum for these bits. Square-hole racks take cage nuts, so there's nothing to tap.
Can I tap strut channel?
Don't. Strut is built so you don't drill or tap it: Unistrut says its system "eliminates welding and drilling", and fittings bolt through their 9/16 in. holes into a channel nut. Standard strut is 12 gauge (0.105 in. on Unistrut P1000), which holds only 1.7 threads of 3/8-16 and 1.4 of 1/2-13, below UL's minimum for those threads. Use a channel nut in the strut, and tap the angle or plate you're bolting to it, where the wall is thick enough.
Data center work
On a data center job the drill tap earns its place in the panel and enclosure work: ground screws, back-panel rails and added holes in threaded cabinet rails. See our data center tools page and the panels and enclosures lineup for the rest of that step.
Can I use a drill tap in an impact driver?
Yes. ITM gives these bits a 1/4 in. hex impact shank and pictures them in an impact driver. The bit is the same in a drill-driver; use whichever gives you better control.
- Center punch the spot so the tip can't walk.
- Put a drop of cutting oil on the spot.
- Hold the driver square to the work and run it at a steady, moderate speed. Let the drill break through before the thread section reaches the metal.
- Keep going until the chamfer touches, then reverse straight back out.
Why they snap: the drill catches as it breaks through thin sheet and yanks the thread section in; the driver tips off square; the part isn't clamped and spins; or the wall is thicker than the thread section. Clamp the work, keep it square, and stay inside the thread length. A 4 in. magnetic bit holder helps reach to the back of a deep box.
Is a drill tap cheaper than a drill and a tap?
To get started, yes, in every size. At our order minimums, the drill taps cost half or less of what the tap drills and plug taps cost in the same size.
| Thread | Drill tap | Drill + plug tap |
|---|---|---|
| 6-32 | $59.32 | $126.60 |
| 8-32 | $60.80 | $132.36 |
| 10-24 | $62.84 | $134.52 |
| 10-32 | $62.84 | $138.12 |
| 12-24 | $66.08 | $157.32 |
| 1/4-20 | $36.72 | $111.12 |
| 5/16-18 | $51.34 | $97.38 |
| 3/8-16 | $51.34 | $118.02 |
| 1/2-13 | $36.03 | $108.66 |
How to read this: each thread size has two bars, and the shorter bar is the cheaper way to start. Both are what one order costs at our minimums. Prices from eldoradotools.com on Nov 19, 2026.
What it means for you: for a few holes in a few sizes, buy the drill taps. Once you're tapping dozens of holes in one size at a bench, the drill and tap route gives you 24 drills and 12 taps for the money.
| Thread | Drill tap order | Tap drill order | Plug tap order |
|---|---|---|---|
| 6-32 | 4 × HDT-0632 | 24 × #36 drill ($1.59 each) | 12 × 071091 ($7.37 each) |
| 8-32 | 4 × HDT-0832 | 24 × #29 drill ($1.83 each) | 12 × 071093 ($7.37 each) |
| 10-24 | 4 × HDT-1024 | 24 × #25 drill ($1.92 each) | 12 × 071095 ($7.37 each) |
| 10-32 | 4 × HDT-1032 | 24 × #21 drill ($2.07 each) | 12 × 071096 ($7.37 each) |
| 12-24 | 4 × HDT-1224 | 24 × #16 drill ($2.57 each) | 12 × 071097 ($7.97 each) |
| 1/4-20 | 2 × HDT-1420 | 24 × #7 drill ($2.86 each) | 6 × 071060 ($7.08 each) |
| 5/16-18 | 2 × HDT-5618 | 12 × F drill ($3.98 each) | 6 × 071062 ($8.27 each) |
| 3/8-16 | 2 × HDT-3816 | 12 × 5/16 in. drill ($4.96 each) | 6 × 071064 ($9.75 each) |
| 1/2-13 | 1 × HDT-1213 | 6 × 27/64 in. drill ($9.26 each) | 3 × 071068 ($17.70 each) |
Drills are Triumph ThunderBits; plug taps are Triumph. The drill picks match our tap drill size chart; the #16 for 12-24 matches ITM's catalog.
Kit or single bits?
If you need four or more of the kit's sizes, buy the kit: any four of them cost more singly at our minimums. The HDT-SET8 holds one each of 6-32, 8-32, 10-24, 10-32, 12-24, 1/4-20, 3/8-16 and 1/2-13 in a case for $167.98. The same eight sizes bought singly at our minimums cost $435.97. The kit has no 5/16-18, so add an HDT-5618 (2 × $25.67) if you need one.
"If you tap four or more sizes, buy the kit. A lot of our drill tap orders already have two or three sizes in them, and at four sizes the kit costs less than the singles every time."
David Castro, President, Eldorado Tools
FAQ
What is a drill tap used for?
A drill tap cuts a threaded through hole in one pass: it drills, taps and chamfers. Trades use it for ground screws, panels, enclosures, rack rails, brackets and light plate.
Can a drill tap make a blind hole?
No. The drill tip runs past the thread, so the thread never reaches the bottom. Use a plug tap and then a bottoming tap.
Can I use a drill tap on stainless steel?
ITM lists steel, cast iron, copper and aluminum for these bits, not stainless. Drill and tap stainless the two-step way.
Do you carry 1/4-28 or metric drill taps?
No. For 1/4-28, use a #3 drill and a 1/4-28 plug tap. For metric threads, see our metric taps.
Do sheet metal screws need a tapped hole?
No. Sheet metal screws and thread-forming screws make their own thread in a drilled hole. Tap the hole when the part takes a machine screw, like a 10-32 ground screw.
What's the difference between a drill bit and a drill tap?
A drill bit only makes the hole. A drill tap makes the hole and cuts the thread in it, so a machine screw threads straight in.
Shop all combination drill taps and taps and dies. Cutting the knockout first? See step drill bits for stainless steel. Cleaning up the hole after? See deburring tools for metal.
Sources: ITM 2026 catalog, p. 35 (HD combination drill tap sizes, thread length, overall length, shank, materials, impact use, HDT-SET8 contents) and p. 34 (12-24 tap drill); UL 50, 13th edition, sections 6.1.7 and 6.1.8 (two full threads; minimum steel thickness per thread pitch); NEC 250.8(A), 2017 text; RACO Boxes, Covers and Accessories catalog, p. A2 (10-32 ground holes, 0.0625 in. box steel); NEMA Technical Bulletin 109 (2015); Unistrut General Engineering Catalog (P1000 thickness, fitting holes, channel nuts); Panduit R2P rack datasheet; Milwaukee, DeWalt and Klein product pages for their drill tap ratings; standard steel sheet gauge chart. Prices from eldoradotools.com on Nov 19, 2026. First drafted Nov 19, 2026.





























































































































