Free shipping over $200 · Supplying commercial contractors across the continental U.S.

Free shipping over $200

Screw Head Types: Which Bit Fits Phillips, Pozidriv, Torx

HomeBlog & GuidesGuidesElectrical

Screw Head Types: Which Bit Fits Phillips, Pozidriv, Torx

Which bit fits which screw head, and what size: Phillips, Pozidriv, square, Torx and hex, plus long Phillips bits for glazing and nut setters for HVAC.

Tools8 in this guide
Read13 min
UpdatedNov 20, 2026

Quick answer: Screw head types come down to the drive: Phillips, Pozidriv, square, Torx, slotted or hex. Match the bit to the drive, then match its size to the screw. A #12 or #14 sheet-metal screw in an aluminum storefront frame takes a #3 Phillips. Reaching down a deep pocket? The ITM T3-090-03 (#3 x 3-1/2 in.) is $1.07 a bit, min. 50. Put a #2 bit in that #3 screw and it will strip the head.

Glaziers go through more bit tips than almost anyone we sell to. Most of what they spend goes on long #2 and #3 Phillips power bits, 2-3/4 to 6 in. long, for driving screws deep inside a frame or track. When one of those bits is a size off, it chews the screw head and you're drilling out a fastener inside a finished frame.

This guide is the cheat sheet for that. It covers which bit fits each screw head, what size goes with each screw, and how long a bit you need. It also covers the head types electricians and HVAC techs run into, plus security heads. Every size rule comes from the sizing chart in ITM's catalog, and every bit named is an ITM bit we sell. All of them are S2 modified steel, heat treated to Rc 58–62, on a 1/4 in. hex shank unless we say 5/16.

Screw head types: which bit fits each drive?

A screw head's drive is the recess you put the bit in. Look straight down at the head and match it to this table. "Head type" also gets used for the head's shape (pan, flat, truss, round). Shape matters for sizing, which the next section covers.

Drive

How to spot it

Bit sizes we sell

Shop

Phillips

Plain cross, tapered walls

#0–#4

Phillips bits

Pozidriv

Cross with four small ticks between the arms on most screws; square-walled

#1–#3

Pozidriv bits

Square (Robertson)

Square hole

#0–#3

Square bits

Torx (star)

Six-pointed star

T6–T55

Torx bits

Torx with pin

Star with a post in the center

T8–T55

Security bits

Slotted

One straight slot

#4-5 to #10-12

Slotted bits

Hex socket (Allen)

Six-sided hole

5/64–1/4 in.

Hex bits

Hex with pin

Hex hole with a post in the center

3/32–5/16 in.

Security bits

Combination (electrical devices)

Slot crossed with a square or Phillips recess

Use a square or Phillips bit (see below)

Square bits

Hex washer head

Six-sided head you grab from outside

Not a bit: a nut setter

Magnetic nut setters

What size bit for each screw size?

The bit size follows the screw's gauge and head shape. These tables are ITM's own sizing chart (catalog, p. 108). A #10 screw can take a #2 or a #3 Phillips depending on the head, so check the row that matches your screw.

Phillips

Screw

Sheet metal / self-drilling (flat, round, oval, stove, binding)

Wood, flat or oval head

Wood, round head

Machine, flat, oval or binding

Machine, round or fillister

Machine, truss, brazier or button

#0, #1

#0

#0

#0

#0

#0

#0

#2, #3, #4

#1

#1

#1

#1

#1

#1

#5

#2

#2

#2

#2

#2

#1

#6, #8

#2

#2

#2

#2

#2

#2

#7

#2

#2

#2

—

—

—

#9

—

#2

#2

—

—

—

#10

#2

#3

#2

#2

#2

#2

#12, #14

#3

#3

#3

#3 (#12)

#3 (#12)

#3 (#12)

#16

—

#3

#3

—

—

—

1/4 in.

—

—

—

#3

#3

#3

5/16 in.

—

—

—

—

#3

—

"—" means ITM's chart has no entry for that screw and head. Source: ITM 2026 catalog, p. 108.

Square (Robertson)

Screw

Tapping / self-drilling

Wood

Machine

#3, #4

#0

#0

#0

#5, #6

#1

#1

#1

#7

#1

#1

—

#8, #10

#2

#2

#2

#9

—

#2

—

#12, #14

#3

#3

#3

Slotted

Machine screw

Slotted bit

#3, #4

ST-025-04 #4-5

#5

ST-025-08 #6-8

#6

ST-025-10 #8-10

#8

ST-025-12 #10-12

Source: ITM 2026 catalog, p. 108. Torx sizes are in their own section below.

Glass and shower: which bits for frames, tracks and hardware?

For storefront and shower work, the bits that matter are long #2 and #3 Phillips power bits. For sheet-metal and self-drilling screws, ITM's chart puts #8 and #10 on a #2 Phillips and #12 and #14 on a #3. A power bit's shaft is slimmer than the hex, so it reaches down a frame pocket and keeps the driver nose clear of the glass.

Job

Bit

Size and length

Price each

Min.

#12 or #14 screw, deep pocket

T3-090-03

#3 x 3-1/2 in.

$1.07

50

#8 or #10 screw, deep pocket

T3-090-02

#2 x 3-1/2 in.

$1.07

50

Deepest reach, #12 or #14

T3-150-03

#3 x 6 in.

$2.24

25

Deepest reach, #8 or #10

T3-150-02

#2 x 6 in.

$2.24

25

Everyday #8 or #10

T3-075-02

#2 x 3 in.

$0.93

50

Pozidriv hardware screws

PZ-075-02

PZ2 x 3 in.

$1.36

50

Holder for 1 in. inserts

BH-075-RC

3 in. magnetic, retaining ring

$3.97

10

Prices from eldoradotools.com on Nov 20, 2026, per piece. "Min." is the order minimum; you pay the per-piece price for each.

These are the same bits our glass and glazing accounts reorder. Long #2 and #3 Phillips power bits make up about 78% of what those accounts spend on bit tips with us, and the BH-075-RC holder shows up on order after order.

"Customer order history tells the story. Almost 80 percent of what glass shops spend on bit tips with us goes to long #2 and #3 Phillips bits, because their screws sit deep in the frame. Reach matters, but get the size right first. A #2 bit in a #3 screw will strip the head."

David Castro, President, Eldorado Tools

On shower doors, the hinge and clamp screws go into tile, so drive them gently. Set a low clutch or finish by hand, and don't let an impact driver crack the tile. Drilling the holes, blocking and anchors are covered in our frameless shower door installation guide. If a hinge or clamp uses hex set screws, the key size is on its instruction sheet. Our hex bits are inch sizes from 5/64 to 1/4 in.; we don't carry metric hex. Drilling the glass itself? See glass drill bits.

Pozidriv vs Phillips: are PH2 and PZ2 the same?

No. A Phillips recess has tapered walls; a Pozidriv recess has parallel walls and extra contact points between the arms. Most Pozidriv screws show four small tick marks on the head; Phillips screws don't. Tool maker PB Swiss puts the mismatch plainly: a Phillips driver in a Pozidriv screw has play, and a Pozidriv driver in a Phillips screw easily damages the screw or the tool. Wiha says the same about wear.

Phillips

Pozidriv

Recess walls

Tapered

Parallel

Head marking

Plain cross

Cross, usually with four ticks

Our 2 in. #2 bit

T3-050-02, $0.51 (min. 75)

PZ-050-02, $1.00 (min. 50)

If a cross-head screw keeps spitting the bit out under load, look for the ticks before you blame the driver. Pozidriv is a registered trademark of the Phillips Screw Company, often misspelled Posidrive or Pozidrive. We sell PZ1, PZ2 and PZ3 bits in 1 and 2 in., and the PZ2 in 3 in. as well.

Phillips also makes a ribbed version called ACR, short for "anti cam-out ribs". Per the Phillips Screw Company, the ribs reduce cam-out when driving and removing. Our ACR bits: ACR-025-02 (#2 x 1 in., $0.52) and ACR-050-02 (#2 x 2 in., $0.75).

What size Torx bit for a #10 screw?

A #10 screw takes a T25 in a pan or Torx washer head, a T20 in a flat (countersunk) head, and a T27 in a socket head cap screw. A 1/4 in. screw takes a T30 in a pan head and a T27 in a flat head. Here is ITM's Torx chart for the common heads. Torx washer heads take the same size as pan heads wherever ITM lists both.

Screw

Pan head

Flat (countersunk) head

Socket head cap screw

Socket set screw

#4

T9

T8

T10

T6

#6

T15

T10

T15

T7

#8

T20

T15

T25

T8

#10

T25

T20

T27

T10

#12

T27

T25

T27

T10

1/4 in.

T30

T27

T30

T20

5/16 in.

—

T40

T45

T27

3/8 in.

T45

T40

T50

T30

Source: ITM 2026 catalog, p. 108. "—" means ITM's chart has no entry.

Our Torx bits come in 1, 2 and 6 in. on a 1/4 in. hex (T6–T40), and T30–T55 in 1-1/4 in. on a 5/16 in. hex. A 5/16 in. hex won't fit a 1/4 in. impact chuck or holder. The most common size runs TX-025-25 (T25 x 1 in., $0.49, min. 75) and TX-050-25 (T25 x 2 in., $0.81, min. 50).

Torx Plus screws (marked "IP") have a squarer lobe. Camcar, which makes them, says a regular Torx bit can remove and reinstall Torx Plus screws in service work. "Star" is the generic name, and it's what ITM calls these bits.

Which bit for receptacle, switch and breaker screws?

Many electrical devices use combination screws: a slot crossed with a square or Phillips recess. Some electricians carry a combination tip (Milwaukee calls theirs ECX, Klein calls theirs Combo-Tip). We don't sell one, but the makers name a plain bit that fits:

Screw

Maker says

Our bit

Price each

Min.

Leviton receptacle terminals (#10-32 triple combination)

Slotted, Phillips #2 or Robertson #1

T3-R25-01 #1 square x 1 in.

$0.45

100

Square D QO and Homeline neutral and ground bars

#2 Robertson (square) or flat blade

T3-R25-02 #2 square x 1 in.

$0.45

100

Same, with reach

Same as above

T3-R50-02 #2 square x 2 in.

$1.03

50

Leviton terminals, Phillips side

Phillips #2

T3-025-02 #2 Phillips x 1 in.

$0.30

125

Prices from eldoradotools.com on Nov 20, 2026, per piece. "Min." is the order minimum; you pay the per-piece price for each.

Sources: Leviton Straight Blade catalog, section D, p. 2; Schneider Electric FAQ FA93974. Check your device's spec sheet; sizes vary by maker. Insert bits need a holder, such as the BH-075-RC. Drilling knockouts? See step drill bits for stainless steel.

HVAC: which driver for hex-head duct screws?

Self-drilling hex washer head screws, the kind ITW Buildex lists for HVAC work, take a nut setter, not a bit tip. The hex size follows the screw. ITW Buildex's TEKS data gives #8 = 1/4 in., #10 and #12 = 5/16 in., and 1/4 in. screws = 3/8 in.

Screw

Hex head

Nut setter (drill/driver)

Price each

Impact nut setter

Price each

#8

1/4 in.

NS-065-16 (min. 20)

$2.15

IMP-065-16 (min. 10)

$3.21

#10, #12

5/16 in.

NS-065-20 (min. 20)

$2.42

IMP-065-20 (min. 10)

$4.25

1/4 in.

3/8 in.

NS-065-24 (min. 10)

$3.47

IMP-065-24 (min. 10)

$5.07

Prices from eldoradotools.com on Nov 20, 2026, per piece. "Min." is the order minimum; you pay the per-piece price for each.

All six are 2-9/16 in. long and magnetic. Shorter and longer lengths are in the magnetic nut setters collection. For panel screws with a Phillips or Torx head, use the tables above.

What bit opens a security screw?

A security screw has a post in the middle of the recess, so a standard bit won't seat. You need the matching bit with a hole in its tip. We carry:

Security head

Sizes

Example

Price each

Min.

Torx with pin

T8–T40 (1 in.), T45–T55 (5/16 in. hex)

TT-025-27 T27

$1.00

50

Hex with pin

3/32–5/16 in.

TH-25-532 5/32 in.

$1.14

50

Phillips tamper

#2, #3

TP-025-02 #2

$2.18

25

Tri-wing

#1–#3

TRI-25-02 #2

$1.30

50

Spanner (snake-eye)

#6–#14

SP-025-08 #8

$1.17

50

Prices from eldoradotools.com on Nov 20, 2026, per piece. "Min." is the order minimum; you pay the per-piece price for each.

How long a bit do you need?

Buy the shortest bit that reaches the screw with the driver clear of the work. A 1 in. insert bit is the cheapest, but it needs a holder. Power bits (2 to 6 in.) go straight in the chuck, and every inch costs more, fastest for Torx:

Bit length (in.)

#2 Phillips ($)

#2 Square ($)

T25 Torx ($)

1 in.

$0.30

$0.45

$0.49

2 in.

$0.51

$1.03

$0.81

2-3/4 in.

$0.86

$1.14

—

3 in.

$0.93

$1.32

—

3-1/2 in.

$1.07

$1.53

—

4 in.

$1.27

$1.60

—

5 in.

$1.75

$2.05

—

6 in.

$2.24

$2.80

$5.32

Price per bit from eldoradotools.com on Nov 20, 2026. T25 Torx comes only in 1, 2 and 6 in.

Long Torx bits are where a holder pays. A 6 in. T25 is $5.32. A $0.49 T25 insert in the BH-150-RC 6 in. magnetic holder ($12.48) costs less after the third worn bit, as long as the holder fits the hole. For 3 or 4 in. of reach, the BH-075-RC ($3.97) and BH-100-RC ($6.51) do the same job.

Why do screws strip, and how does the right bit stop it?

What you see

Likely cause

Fix

Bit climbs out of a cross-head screw

#2 bit in a #3 screw, or a Phillips bit in a Pozidriv screw

Check the size table and look for Pozidriv ticks

Bit tip rounds off after a few screws

Worn bit, or a standard bit in an impact driver

Replace it; use impact-rated bits in an impact

Bit wobbles in a long reach

Insert in a loose holder, or bit too long

Use a power bit or a ring-lock holder; shortest length that reaches

Star bit spins in a Torx screw

One size too small (T20 in a T25)

Go up a size; it should drop in with no play

Bit won't seat at all

Security screw with a center post

Use the matching pin bit

Driving with an impact driver all day? Our impact vs regular bit tips guide covers ITM's Blue-Shock line, which ITM rates at up to 12x the life of standard bits.

FAQ

What are the main screw head types?

By drive: Phillips, Pozidriv, square (Robertson), Torx (star), slotted and hex, plus security versions with a center post. By shape: pan, flat, oval, round, truss, binding and hex washer. You need both to pick the right bit size.

Can I use a Phillips bit on a Pozidriv screw?

Only gently. A Phillips bit fits loosely in a Pozidriv recess and slips under torque. Use a Pozidriv bit of the same number.

What size Phillips bit for a #10 screw?

A #2 for sheet-metal, round-head wood and machine screws; a #3 for a flat or oval-head wood screw (ITM's chart).

What is a Robertson screw?

A screw with a square recess, also called a square drive. Sizes #0 to #3; #2 fits #8 and #10 screws.

What size Torx bit for a 1/4 in. screw?

T30 for a pan head and T27 for a flat head (ITM's chart).

Does a Torx bit fit a Torx Plus screw?

Yes, for removing and reinstalling in service work, according to Camcar. Use a Torx Plus bit for production driving.

What bit do I need for a hex head screw?

An outside hex head takes a nut setter, not a bit: 1/4 in. for #8 self-drilling screws, 5/16 in. for #10 and #12, and 3/8 in. for 1/4 in. screws.

Do you sell ECX or combination bits?

No. Leviton device terminals take a #1 square or #2 Phillips, and Square D neutral and ground bars take a #2 square. We sell both.

Shop all bit tips, bit tip holders and magnetic nut setters.

Sources: ITM 2026 catalog, p. 108 (Phillips, slotted, square and star sizing chart), pp. 110–113 (bit specs: S2 modified steel, Rc 58–62, lengths, shanks); ITM Blue-Shock flyer; PB Swiss Tools and Wiha on Phillips and Pozidriv; Phillips Screw Company Pozidriv, ACR and trademark documents; Camcar on Torx Plus; Leviton Straight Blade catalog, section D, p. 2; Schneider Electric FAQ FA93974; ITW Buildex TEKS product data. Prices from eldoradotools.com on Nov 20, 2026. First drafted Nov 20, 2026.

← Back to Blog & Guides
Vanessa Franchesca
Written by Vanessa Franchesca

Vanessa Franchesca is a highly skilled professional with a passion for policy, marketing, and digital strategy. With a proven track record of success, she has excelled in developing and implementing effective campaigns. Vanessa's expertise lies in policy development, social media management, content creation, and brand development. Her strong analytical skills and creativity allow her to deliver impactful results for her clients. With a Bachelor's degree in Social Sciences from Harvard University’s Extension School with a concentration in Government, and years of experience in the industry, Vanessa is dedicated to driving growth and helping businesses and people thrive in the digital landscape. Connect with her on LinkedIn to explore new opportunities and stay updated on the latest marketing trends.