HomeBlog & GuidesGuidesMetal Fabrication
How to Use a Tap and Die Set: Fractional, Machine Screw, NPT
Which tap fits your bolt, screw or pipe fitting, how many taps a hole needs, how to use a tap and a die by hand, and when a set costs less than singles.
Quick answer: A tap and die set cuts threads two ways. The tap cuts them inside a drilled hole, and the die cuts them on the outside of a rod or bolt. Pick the tap by the fastener. Numbered screws (#4 to #12) take a machine screw tap. Bolts 1/4 in. and up take a fractional tap. Pipe fittings take a tapered NPT pipe tap. A hole that goes all the way through needs one plug tap, like the 1/4-20 plug, 071060 ($7.08, sold in 6s). A blind hole needs a plug tap, then a bottoming tap.
Threading a hole is a ten-minute job when the parts on the bench match the hole. It turns into an afternoon of drilling out a broken tap when they don't. Most of the trouble starts before the tap touches metal: the wrong thread family, the wrong tip on the tap, or a wrench that doesn't fit it.
This guide sorts that out for fab shops and plumbers. It covers which kind of tap fits your bolt, screw or fitting, how many taps a hole needs, how to cut threads by hand with a tap or a die, and when a full set costs less than buying taps one at a time. The taps are Triumph ThunderTap hand taps, made in the USA from M2 high-speed steel. People also call them thread taps, hand taps, or by the thread, as in "a 3/8-16 tap". For the drill bit that goes with each tap, use our tap drill size chart.
Which is the tap and which is the die?
A tap is the fluted tool that cuts threads inside a hole, so a bolt or screw can thread into the part. A die is the round or hex block that cuts threads on the outside of a rod or bolt, so a nut can thread on. Both come in a tap and die set, sized in matching pairs.
| Tool | Cuts threads | Use it for | What turns it | Where we sell it |
|---|---|---|---|---|
| Tap | Inside a drilled hole | Tapping plate, brackets, flanges, tanks and fittings for a bolt, screw or pipe | A tap wrench (T-handle or straight handle) on the square end | Singly: fractional, machine screw and pipe taps |
| Round adjustable die | Outside a rod or bolt | Cutting new threads on bare rod; the split lets you set the fit | A die stock (two-handled holder) | Inside the round-die tap and die sets |
| Hex die | Outside a rod or bolt | Cutting or chasing threads where a die stock won't swing | An open-end wrench or socket on the hex | Inside the hex-die tap and die sets |
| Hex rethreading die | Outside a rod or bolt | Cleaning up and repairing threads that are already there | A wrench or socket on the hex | The Walter 3350 rethreading die sets |
We don't sell single cutting dies. If you need dies, they come in a set, which also brings the matching taps and holders.
Fractional vs machine screw vs pipe taps: which one fits my bolt?
The tap family follows the fastener. Read the size on the bolt, screw or fitting, and the way it's written tells you which family to buy.
| Tap family | How the size is written | Fits | Sizes we stock | Price each | Sold in |
|---|---|---|---|---|---|
| Machine screw taps | Number, then threads per inch: 10-24 | Screws under 1/4 in.: #4 (0.112 in.) to #12 (0.216 in.) | #4-40 to #12-28 | $7.37 to $10.33 | 12s |
| Fractional taps | Diameter in inches, then threads per inch: 3/8-16 | Bolts and cap screws 1/4 in. and up | 1/4-20 to 1-1/8-7 | $7.08 to $132.82 | 6s (1/4 to 3/8 in.), 3s (7/16 and 1/2 in.), 2s (9/16 and 5/8 in.), singly from 3/4 in. |
| Pipe taps (NPT) | Nominal pipe size, then threads per inch: 1/2-14 NPT | Pipe fittings, plugs, gauges and bungs | 1/8 to 1-1/2 NPT | $30.98 to $283.33 | 2s (1/8 and 1/4 NPT), singly from 3/8 NPT |
Prices from eldoradotools.com on Nov 19, 2026, per tap.
Machine screw and fractional taps cut straight threads with the same thread form. The only difference is the size range, so a 10-24 machine screw tap and a 1/4-20 fractional tap belong to the same family of Unified threads.
A pipe tap is different in two ways. First, the size names the pipe, not the thread. A 1/2 in. NPT thread is cut for pipe that measures 0.840 in. across, so a 1/2 NPT pipe tap is much bigger than a 1/2-13 bolt tap. Second, NPT threads taper 3/4 in. per foot on the diameter, so the fitting wedges tight and seals. A pipe tap only comes with a taper tip because the thread itself is tapered.
Coarse (UNC) or fine (UNF)?
Every size has a coarse and a fine thread. A 3/8 in. bolt is 3/8-16 in coarse (UNC, often written NC) and 3/8-24 in fine (UNF, or NF). Coarse is the everyday thread for structural work and soft metals. Fine shows up on equipment and automotive parts where a bolt needs finer adjustment or thin walls need more threads. Match the bolt: a 3/8-24 bolt won't thread into a 3/8-16 hole. We stock both for every size from #6 to 1 in. (#4 and 1-1/8 in. are coarse only).
Taper, plug or bottoming: how many taps does my hole need?
A through hole needs one tap, a plug tap. A blind hole, one that stops inside the part, needs a plug tap and then a bottoming tap. The difference between the three is how many threads at the tip are ground down (the chamfer), which decides how easily the tap starts and how close to the bottom it cuts full threads.
| Tap | Chamfer at the tip | Use it for | 1/2-13 example |
|---|---|---|---|
| Taper | 7 to 10 threads | Starting straight in hard or thick stock, or tapping by eye with no guide | 071008, $17.70 |
| Plug | 3 to 5 threads | Most jobs. Finishes a through hole on its own | 071068, $17.70 |
| Bottoming | 1 to 2 threads | The last few threads at the bottom of a blind hole, after the plug | 071108, $17.70 |
Chamfer lengths from Walter's ThunderTap product records. Prices from eldoradotools.com on Nov 19, 2026; 1/2-13 taps are sold in 3s.
Every fractional and machine screw size we carry comes in all three. A taper, plug and bottoming tap in the same size cost the same, so the choice is about the hole, not the price. Never start a hole with a bottoming tap. With only one or two lead threads, the bottoming tap has nothing to steer it straight.
Which tap do I buy for my job?
These are the jobs fab shops and plumbers ask us about most, with the exact tap and what the first order costs at our minimums.
| Job | Thread | Buy | Price each | Sold in | First order |
|---|---|---|---|---|---|
| Bolt holes through 3/8 in. plate or angle | 1/4-20 | 071060 plug tap | $7.08 | 6 | $42.48 |
| Bolt holes through a bracket or base plate | 1/2-13 | 071068 plug tap | $17.70 | 3 | $53.10 |
| Blind holes in a flange or thick block | 3/8-16 | 071064 plug, then 071104 bottoming | $9.75 each | 6 each | $117.00 |
| Screw holes in sheet, boxes and panels, by hand | 10-24 | 071095 plug tap | $7.37 | 12 | $88.44 |
| Same holes, drilled and tapped in one pass with an impact or drill | 10-24 | HDT-1024 combination drill tap | $15.71 | 4 | $62.84 |
| Gauge, drain or sensor port | 1/4-18 NPT | 071251 pipe tap | $34.65 | 2 | $69.30 |
| Port in a tank, manifold or plate | 1/2-14 NPT | 071253 pipe tap | $70.83 | 1 | $70.83 |
| Bung or drain in a tank | 3/4-14 NPT | 071254 pipe tap | $96.82 | 1 | $96.82 |
| Cleaning up cut all-thread for pipe hangers | 3/8-16 and 1/2-13 | 3350CC10 NC hex rethreading die set, 1/4 to 1 in. | $251.82 | 1 | $251.82 |
Prices from eldoradotools.com on Nov 19, 2026. "Sold in" is the order minimum; you pay the per-piece price for each one.
"Buy the spares. A tap rarely breaks on the first hole. It breaks on the fortieth, when you're behind and leaning on it. That's why we sell them in sixes and twelves."
David Castro, President, Eldorado Tools
Find the exact tap for your thread
Pick the job, the thread and the kind of hole. The Thread Job Picker names the taps, the wrench that holds them and what the first order costs. Every tap we stock is in the table under it.
| Thread | Family | Taper | Plug | Bottoming | Price each | Sold in |
|---|---|---|---|---|---|---|
| #4-40 | Machine screw, coarse (UNC) | 071040 | 071090 | 071140 | $10.33 | 12 |
| #6-32 | Machine screw, coarse (UNC) | 071041 | 071091 | 071141 | $7.37 | 12 |
| #6-40 | Machine screw, fine (UNF) | 071042 | 071092 | 071142 | $7.37 | 12 |
| #8-32 | Machine screw, coarse (UNC) | 071043 | 071093 | 071143 | $7.37 | 12 |
| #8-36 | Machine screw, fine (UNF) | 071044 | 071094 | 071144 | $7.37 | 12 |
| #10-24 | Machine screw, coarse (UNC) | 071045 | 071095 | 071145 | $7.37 | 12 |
| #10-32 | Machine screw, fine (UNF) | 071046 | 071096 | 071146 | $7.37 | 12 |
| #12-24 | Machine screw, coarse (UNC) | 071047 | 071097 | 071147 | $7.97 | 12 |
| #12-28 | Machine screw, fine (UNF) | 071048 | 071098 | 071148 | $7.97 | 12 |
| 1/4-20 | Fractional, coarse (UNC) | 071000 | 071060 | 071100 | $7.08 | 6 |
| 1/4-28 | Fractional, fine (UNF) | 071001 | 071061 | 071101 | $7.08 | 6 |
| 5/16-18 | Fractional, coarse (UNC) | 071002 | 071062 | 071102 | $8.27 | 6 |
| 5/16-24 | Fractional, fine (UNF) | 071003 | 071063 | 071103 | $8.27 | 6 |
| 3/8-16 | Fractional, coarse (UNC) | 071004 | 071064 | 071104 | $9.75 | 6 |
| 3/8-24 | Fractional, fine (UNF) | 071005 | 071065 | 071105 | $9.75 | 6 |
| 7/16-14 | Fractional, coarse (UNC) | 071006 | 071066 | 071106 | $18.13 | 3 |
| 7/16-20 | Fractional, fine (UNF) | 071007 | 071067 | 071107 | $18.13 | 3 |
| 1/2-13 | Fractional, coarse (UNC) | 071008 | 071068 | 071108 | $17.70 | 3 |
| 1/2-20 | Fractional, fine (UNF) | 071009 | 071069 | 071109 | $17.70 | 3 |
| 9/16-12 | Fractional, coarse (UNC) | 071010 | 071070 | 071110 | $31.87 | 2 |
| 9/16-18 | Fractional, fine (UNF) | 071011 | 071071 | 071111 | $31.87 | 2 |
| 5/8-11 | Fractional, coarse (UNC) | 071012 | 071072 | 071112 | $34.23 | 2 |
| 5/8-18 | Fractional, fine (UNF) | 071013 | 071073 | 071113 | $34.23 | 2 |
| 3/4-10 | Fractional, coarse (UNC) | 071014 | 071074 | 071114 | $46.33 | 1 |
| 3/4-16 | Fractional, fine (UNF) | 071015 | 071075 | 071115 | $46.33 | 1 |
| 7/8-9 | Fractional, coarse (UNC) | 071016 | 071076 | 071116 | $73.80 | 1 |
| 7/8-14 | Fractional, fine (UNF) | 071017 | 071077 | 071117 | $73.80 | 1 |
| 1-8 | Fractional, coarse (UNC) | 071018 | 071078 | 071118 | $91.50 | 1 |
| 1-12 | Fractional, fine (UNF) | 071019 | 071079 | 071119 | $91.50 | 1 |
| 1-1/8-7 | Fractional, coarse (UNC) | 071020 | 071080 | 071120 | $132.82 | 1 |
| 1/8-27 NPT | Pipe (NPT) | 071250 | None | None | $30.98 | 2 |
| 1/4-18 NPT | Pipe (NPT) | 071251 | None | None | $34.65 | 2 |
| 3/8-18 NPT | Pipe (NPT) | 071252 | None | None | $43.38 | 1 |
| 1/2-14 NPT | Pipe (NPT) | 071253 | None | None | $70.83 | 1 |
| 3/4-14 NPT | Pipe (NPT) | 071254 | None | None | $96.82 | 1 |
| 1-11-1/2 NPT | Pipe (NPT) | 071255 | None | None | $147.57 | 1 |
| 1-1/4-11-1/2 NPT | Pipe (NPT) | 071256 | None | None | $209.55 | 1 |
| 1-1/2-11-1/2 NPT | Pipe (NPT) | 071257 | None | None | $283.33 | 1 |
Prices from eldoradotools.com on Nov 19, 2026, per tap. Taper, plug and bottoming taps in the same thread cost the same. Pipe taps come as taper taps only.
How do I use a tap by hand?
To tap a hole by hand, drill the right size, chamfer the edge, start the tap square, and turn it a full turn forward then back to break the chip. Here is the full sequence.
- Drill the tap drill size. Look up the drill for your thread in the tap drill size chart. A hole drilled too small makes the tap work too hard and is a common reason taps break.
- Chamfer the top of the hole. A light countersink gives the tap a place to center and stops the first thread from raising a burr. See deburring tools for metal.
- Fit the right wrench. Use a tap wrench sized for the tap, so you can feel the cut and don't bend the tap. The 02W100 T-handle holds #6 to 1/4 in. taps ($22.42, sold in 2s), and the 02W200 holds 1/4 to 1/2 in. taps ($26.46).
- Start square. Press down lightly and turn until the tap bites. Check it against a square from two sides, 90 degrees apart, before you go deeper.
- Use cutting fluid on steel and stainless.
- Turn forward, then back. Walter's own advice for its taps is one full turn clockwise, then turn back to break the chip. Keep both hands on the wrench and even pressure on both sides.
- In a blind hole, clear the chips. Back the tap out, blow or brush out the chips, then finish the last threads with the bottoming tap.
For taps over 1/2 in., you need a larger straight-handle tap wrench. A 1/4 to 1 in. adjustable tap wrench comes in the 2000H38, 2000H25 and 2000H63 sets. To buy one on its own, call us at (833) 4-ETOOLS.
| Tap wrench | Holds taps | Price each | Sold in |
|---|---|---|---|
| 02W100 T-handle, ratchet | #6 to 1/4 in. | $22.42 | 2 |
| 02W200 T-handle, ratchet | 1/4 to 1/2 in. | $26.46 | 1 |
| T-handle wrench, in sets | #0 to 3/8 in. | In the 2000H38, 2000R38, 2000H63 and 2000R63 sets | Call to buy alone |
| Straight-handle adjustable wrench, in sets | 1/4 to 1 in. | In the 2000H38, 2000R38, 2000H25, 2000R25, 2000H63 and 2000R63 sets | Call to buy alone |
Capacities from Walter's product records. Prices from eldoradotools.com on Nov 19, 2026.
Can I drill and tap in one step?
Yes, in sheet and thinner plate, with a combination drill tap. The ITM HD combination drill taps have a drill point, the thread and a chamfer on one M2 high-speed steel bit with a 1/4 in. hex impact shank. They come in 6-32 through 1/2-13. The drill point leads the threads, so they are made for holes that go through.
| Drill tap | Thread | Price each | Sold in |
|---|---|---|---|
| HDT-0632 | #6-32 | $14.83 | 4 |
| HDT-0832 | #8-32 | $15.20 | 4 |
| HDT-1024 | #10-24 | $15.71 | 4 |
| HDT-1032 | #10-32 | $15.71 | 4 |
| HDT-1224 | #12-24 | $16.52 | 4 |
| HDT-1420 | 1/4-20 | $18.36 | 2 |
| HDT-5618 | 5/16-18 | $25.67 | 2 |
| HDT-3816 | 3/8-16 | $25.67 | 2 |
| HDT-1213 | 1/2-13 | $36.03 | 1 |
Prices from eldoradotools.com on Nov 19, 2026.
How do I use a die to cut threads on a rod or bolt?
To cut threads with a die, chamfer the end of the rod, start the die square from its chamfered side, and turn it forward and back the same way you turn a tap.
- Chamfer the rod end. Grind or file a short bevel so the die has something to start on.
- Clamp the rod upright in a vise, close to the jaws so it doesn't flex.
- Set the die in its holder. A round adjustable die goes in a die stock, with the adjusting screw snugged so the split is closed for the first pass. A hex die takes a wrench or socket.
- Start from the chamfered side of the die, the side where the threads open wider. Keep the die flat to the rod, using cutting fluid on steel.
- Turn forward and back to break the chip, then test with a nut. If the nut is tight, open the round die a touch and take a second pass.
To repair threads instead of cutting new ones, use a rethreading die. Walter makes its 3350 hex rethreading dies from carbon steel for repairing damaged threads and cleaning rust and paint off a threaded part. That makes them the right tool for the end of a cut piece of all-thread, a bolt that's been hammered, or a stud that's rusted. Buy 3350CC10 for coarse threads, 3350CF10 for fine, or 3350C20 for both ($412.85).
| Rethreading die set | Threads | Sizes | Price |
|---|---|---|---|
| 3350CC10, 10 pieces | Coarse (NC) | 1/4 to 1 in. | $251.82 |
| 3350CF10, 10 pieces | Fine (NF) | 1/4 to 1 in. | $251.82 |
| 3350C20, 20 pieces | Coarse and fine (NC and NF) | 1/4 to 1 in. | $412.85 |
Prices from eldoradotools.com on Nov 19, 2026.
How deep do I tap a pipe thread?
Tap a pipe thread a little at a time and test it with the actual fitting. Because NPT is tapered, every extra turn of the tap makes the hole bigger at the top, and a pipe hole tapped too deep won't seal. The pipe thread standard puts hand-tight engagement at about 4 to 5 threads, for example 4.48 threads on 1/2 NPT. So tap in short steps, back the tap out, and try the fitting by hand. Stop when the fitting threads in by hand and stops with threads still showing. The wrench turns finish the seal.
These pipe taps cut threads inside a hole. To thread the outside of a pipe, you need a pipe threader with NPT dies, which we don't sell. Call us if you need one quoted.
Should I buy a tap and die set or single taps?
Buy a set when you need more than a few sizes. Because single taps are sold in 2s, 3s, 6s and 12s, buying one coarse plug tap in each size from 1/4 to 3/4 in. costs more than the whole 2000HC20 set, which also has the dies and two tap wrenches.
| Sizes you need (1/4 in. up) | Single plug taps at our minimums ($) | 2000HC20 set ($) |
|---|---|---|
| 1 | 42.48 | 406.02 |
| 2 | 92.10 | 406.02 |
| 3 | 150.60 | 406.02 |
| 4 | 204.99 | 406.02 |
| 5 | 258.09 | 406.02 |
| 6 | 321.83 | 406.02 |
| 7 | 390.29 | 406.02 |
| 8 | 436.62 | 406.02 |
How to read this: each row adds the next coarse size (1/4-20, 5/16-18, 3/8-16, 7/16-14, 1/2-13, 9/16-12, 5/8-11, 3/4-10) at its order minimum. Prices from eldoradotools.com on Nov 19, 2026.
What it means for you: need all eight coarse sizes from 1/4 to 3/4 in.? The set costs $30.60 less than the taps alone and adds the dies. Need four sizes or fewer? Single taps cost about half as much.
The gap is bigger at the small end. One plug tap in each of the 17 threads in the 2000H38 set (#4-40 to 1/2-20, plus 1/8 NPT) costs $1,151.50 at our minimums, because machine screw taps are sold in 12s. The set is $476.39.
| Set | Threads | Dies | Wrenches and holders | Price |
|---|---|---|---|---|
| 2000HC20, 18 pieces | UNC 1/4 to 3/4 in. | Hex, carbon steel | #7 to 1/2 in. adjustable tap wrench; #12 to 1/2 in. T-handle | $406.02 |
| 2000HF20, 18 pieces | UNF 1/4 to 3/4 in. | Hex, carbon steel | Same as 2000HC20 | $406.02 |
| 2000RC20, 20 pieces | UNC 1/4 to 3/4 in. | Round adjustable | Same, plus a 1-1/2 in. die stock and screwdriver | $464.83 |
| 2000RF20, 20 pieces | UNF 1/4 to 3/4 in. | Round adjustable | Same as 2000RC20 | $464.83 |
| 2000H38, 36 pieces | UNC and UNF #4 to 1/2 in., plus 1/8 NPT | Hex, carbon steel | 1/4 to 1 in. adjustable tap wrench; #0 to 3/8 in. T-handle | $476.39 |
| 2000R38, 38 pieces | UNC and UNF #4 to 1/2 in., plus 1/8 NPT | Round adjustable | Same, plus a 1 in. die stock and screwdriver | $501.19 |
| 2000H25, 23 pieces | UNC and UNF 9/16 to 1 in., plus 1/4 NPT | Hex, carbon steel | 1/4 to 1 in. adjustable tap wrench | $1,055.00 |
| 2000R25, 25 pieces | UNC and UNF 9/16 to 1 in., plus 1/4 NPT | Round adjustable | Same, plus a 2 in. die stock and screwdriver | $1,182.88 |
| 2000H63, 58 pieces | UNC and UNF #4 to 1 in., plus 1/8 and 1/4 NPT | Hex, carbon steel | #7 to 1/2 in. and 1/4 to 1 in. adjustable tap wrenches; #0 to 3/8 in. T-handle | $1,566.52 |
| 2000R63, 63 pieces | UNC and UNF #4 to 1 in., plus 1/8 and 1/4 NPT | Round adjustable | Same, plus 1 in. and 2 in. die stocks and two screwdrivers | $1,726.38 |
Contents from our product pages, checked against Walter's set records. Prices from eldoradotools.com on Nov 19, 2026. Each set has one tap per thread size.
Hex dies are carbon steel and work with an ordinary wrench, which helps in tight spots. Round adjustable dies let you open or close the thread fit, which helps when a nut is too tight on the first pass.
FAQ
What is a tap and die set used for?
A tap and die set cuts new threads and repairs damaged ones. The taps thread holes for bolts, screws and pipe fittings, and the dies thread rods and bolts.
Can you rethread a bolt with a tap and die set?
Yes. Run the matching die over the bolt to chase out damaged threads, and run the matching tap through a damaged hole. For rusty or hammered threads, a carbon steel hex rethreading die like the 3350CC10 set is made for that job.
What tap wrench do I need for a 3/4 in. tap?
A straight-handle adjustable tap wrench rated for 3/4 in. taps. Our T-handle wrenches stop at 1/2 in. The 1/4 to 1 in. adjustable wrench comes in the 2000H38, 2000H25 and 2000H63 sets; call us to order one on its own.
Can I use a regular tap for a pipe fitting?
No. A pipe fitting needs a tapered NPT pipe tap. A straight bolt tap in the same nominal size is the wrong diameter and the wrong thread, and the fitting won't seal.
Are these taps made in the USA?
Yes. Triumph ThunderTap taps are made in the USA from M2 high-speed steel with a bronze oxide finish.
Do you sell metric taps?
Yes, in a separate collection: metric taps.
Shop all taps and dies. Need the drill for your tap? Use the tap drill size chart. Drilling the tap hole in steel? See how to choose drill bits for metal, and for tap drills over 1/2 in., Silver and Deming bits.
Sources: Walter Surface Technologies product records for Triumph ThunderTap taps, tap wrenches, tap and die sets and 3350 rethreading die sets (material, chamfer lengths, wrench capacities, set contents, uses); Walter, "Tapping into your Tap Knowledge" (hand-tapping method); OSG, Tap Drill Sizes and Pitch Diameter Limits, Vol. 3 (2024) (threads per inch); National Bureau of Standards Handbook H28 (1957), Parts I and II (machine screw diameters, NPT pipe sizes, taper and hand-tight engagement). Prices from eldoradotools.com on Nov 19, 2026. First drafted Nov 19, 2026.






























































































































