HomeBlog & GuidesGuidesFoundation & Basement Repair
SDS Chisel Bit Guide: Point, Flat, Scaling or Tile for Demo
Quick answer: Pick an SDS chisel bit by what you're taking off and what's under it. A bull point cracks concrete (7000BP, 12 in. SDS-Max, $15.07). A flat chisel splits and squares the edge (7010FC, $15.07). A scaling chisel shaves mortar beds and scale in wide strips (3122SC, 2-1/2 in. SDS-Plus, $35.52). A tile chisel pops floor tile (3175TC, $31.36), and a floor scraper strips whole rooms (2244FS, $86.20). Match the shank to your rotary hammer and run every chisel in hammer-only mode.
Every demo job is a stack of layers: tile on thinset on a slab, a slab on gravel, a mortar bed on lath. The chisel you want depends on the layer you're removing and the layer you need to leave alone. This guide starts every section with that stack, then names the exact part, its size and its price.
People call these SDS chisels, chisel bits, demo bits, rotary hammer chisels and chipping bits. A bull point is also a point chisel or moil point. A scaling chisel is sometimes sold as a wide chisel, and a tile chisel as a tile remover or tile stripper. All of them fit the same two shanks: SDS-Plus and SDS-Max.
What is an SDS chisel bit, and can a hammer drill use one?
An SDS chisel bit is a chisel with an SDS shank, made for a rotary hammer that can switch off rotation and only hammer. A regular hammer drill can't run one. A hammer drill has a three-jaw chuck that can't grip the slotted SDS shank, and it has no hammer-only mode, so the chisel would spin.
Bosch, Milwaukee and Makita all say the same thing in their rotary hammer manuals: set the hammer to hammer-only (chisel) mode before you chisel, and never chisel in hammer-drill mode. Makita and Milwaukee add that you shouldn't switch modes while the motor is running. Most SDS hammers also let you turn the chisel to the angle you want and lock it there; Bosch calls this Vario-Lock. Check your manual for how many positions yours has.
The shank has to match the hammer. SDS-Plus is the 10 mm shank on the 1 in. class of rotary hammers. SDS-Max is the 18 mm shank on larger hammers. If you're not sure which yours takes, look at the bit end: SDS-Plus has two open slots, SDS-Max has three. Our SDS Plus vs SDS Max guide covers the shank decision in full.
Which SDS chisel for which job?
Find your job in the table, then read across for the layer stack and the part for each shank. "None" means we don't sell that tool in that shank.
| Job | Layer stack | SDS-Plus | SDS-Max |
|---|---|---|---|
| Lift floor tile off a slab | Tile on thinset, over a slab | 3175TC tile chisel, 3 x 6-1/2 in., $31.36; 2244FS floor scraper, 4 x 10 in., $86.20, for a whole room | 7070FS floor scraper, 6 x 25 in., $341.82; 7030SC scaling chisel, 3 x 12 in., $30.63, for edges |
| Break out a mud bed or wall tile on mortar | Tile on a mortar bed, over lath or block | 3122SC scaling chisel, 2-1/2 x 10 in., $35.52 | 7030SC scaling chisel, 3 x 12 in., $30.63; 7032SC scaling chisel, 3 x 18 in., $38.28, for a floor bed, worked standing |
| Strip vinyl, VCT or glued-down flooring | Resilient floor on adhesive, over a slab | 2244FS floor scraper, 4 x 10 in., $86.20 | 7070FS floor scraper, 6 x 25 in., $341.82 |
| Break up a concrete slab | Slab on grade | 3100BP bull point, 10 in., $16.61 (min. 2), small patches only | 7005BP bull point, 18 in., $18.78 (min. 2); 7015FC flat chisel, 1 x 18 in., $18.78 (min. 2) |
| Trench a slab for a drain line | Slab, saw-cut both sides, drain below | 3118FC flat chisel, 3/4 x 18 in., $19.94 (min. 2), short runs only | 7005BP bull point, 18 in., $18.78 (min. 2); 7015FC flat chisel, 1 x 18 in., $18.78 (min. 2); 7028SC scaling chisel, 2 x 18 in., $32.03 |
| Break out a footing or foundation trench | Footing or stem wall, below grade | None. This is an SDS-Max or breaker job | 7024BP bull point, 24 in., $34.86; 7024FC flat chisel, 1 x 24 in., $34.86; 7029SC scaling chisel, 2 x 24 in., $36.20 |
| Chase a channel for pipe or conduit | Wall or floor, channel for pipe or conduit | 3120GC gouge chisel, 7/8 x 10 in., $29.61 | 7075GC gouge chisel, 1 x 12 in., $50.16 |
| Chip in a tight spot (under a vanity, by a flange) | Tight space, short reach | 2110FC MINI flat, 3/4 x 5-1/2 in., $16.78 (min. 2); 2100BP MINI point, 5-1/2 in., $15.13 (min. 2) | None. Every SDS-Max part we sell is at least 9-7/8 in. long |
| Clean out a seam or joint | Block, brick or slab seam | None | 7060SM seam tool, 1-1/8 x 12 in., $32.79 |
| Rough up concrete for a patch or overlay | Slab or step, surface only | None | 7045BT bushing tool, 1-7/8 x 9-7/8 in., $97.11; 7048CB carbide bushing tool, 1-1/2 x 12 in., $120.26 |
| Dig hard clay or hardpan | Soil around a footing | None | 7065CS clay spade, 5-3/8 x 16 in., $120.69 |
| Cut asphalt | Asphalt patch or trench edge | None | 7055PH asphalt cutter, 3-1/2 x 16 in., $117.98 |
Prices checked on eldoradotools.com on Nov 13, 2026, per piece. Each chisel is sold individually; where a minimum order applies, it is shown.
Bull point or flat chisel for breaking concrete?
Slab on grade, 4 in. thick, gravel under it. Use both: the bull point cracks the concrete and the flat chisel splits the cracked piece free and squares the edge you're keeping. A point puts all the hammer's blows on one spot, so it starts a break. A flat spreads them along a line, so it cuts to a line and pries a chunk loose from below.
Start at an edge or an existing crack, never in the middle of the slab. A chisel driven into solid concrete with nowhere for the pieces to go just buries itself. Work in from the edge, taking bites a few inches back, and let each piece fall into the hole you've already opened.
Pick the length by how you'll stand. A 5-1/2 in. MINI chisel is for tight spots where the hammer barely fits. A 10 or 12 in. chisel is for work at knee height or on a wall. An 18 in. chisel lets you break a slab standing up. A 24 in. chisel reaches into a trench while you stand at the edge.
| Length | SDS-Plus bull point | SDS-Plus flat chisel | SDS-Max bull point | SDS-Max flat chisel | Where you use it |
|---|---|---|---|---|---|
| 5-1/2 in. (MINI) | 2100BP, $15.13 (min. 2) | 2110FC, $16.78 (min. 2) | None | None | Under a vanity, beside a toilet flange, inside a cabinet |
| 10 in. | 3100BP, $16.61 (min. 2) | 3110FC, $16.61 (min. 2) | None | None | Kneeling, on a wall, small patches |
| 12 in. | None | None | 7000BP, $15.07 (min. 2) | 7010FC, $15.07 (min. 2) | Kneeling or at knee height |
| 18 in. | None | 3118FC, $19.94 (min. 2) | 7005BP, $18.78 (min. 2) | 7015FC, $18.78 (min. 2) | Standing on a slab |
| 24 in. | None | None | 7024BP, $34.86 | 7024FC, $34.86 | Standing at the edge of a trench |
SDS-Plus flats are 3/4 in. wide; SDS-Max flats are 1 in. wide. For a whole slab, use SDS-Max. An SDS-Plus hammer will break out a 2 x 2 ft patch for a repair, but Hilti notes that a combi hammer's chisel mode is for light work, and heavy breaking calls for a breaker.
Prices checked on eldoradotools.com on Nov 13, 2026, per piece. Each chisel is sold individually; where a minimum order applies, it is shown.
What is a scaling chisel used for?
Mortar bed, wall tile, scale or a coating, over block, brick or a slab. A scaling chisel shaves a wide layer off a harder surface: an old mortar bed, wall tile on mortar, or a coating or scale on concrete. The wide blade spreads the hammer's blows, so it lifts a layer instead of digging a hole.
Width decides speed and control. A 1-1/4 or 1-1/2 in. blade works in a corner or along a narrow strip. A 2 or 2-1/2 in. blade is the everyday size for walls. A 3 in. SDS-Max blade moves a floor bed fastest. On a wall, work top-down and score a thick bed into squares with a point first, so the pieces come away in hand-size chunks.
| Blade width | SDS-Plus | SDS-Max |
|---|---|---|
| 1-1/4 in. | 2115SC 1-1/4 x 5-1/2 in., $21.04 (min. 2) | None |
| 1-1/2 in. | 3115SC 1-1/2 x 10 in., $30.89 | 7020SC 1-1/2 x 12 in., $23.39 (min. 2) |
| 2 in. | None | 7025SC 2 x 12 in., $24.45 (min. 2); 7028SC 2 x 18 in., $32.03; 7029SC 2 x 24 in., $36.20 |
| 2-1/2 in. | 3122SC 2-1/2 x 10 in., $35.52 | None |
| 3 in. | None | 7030SC 3 x 12 in., $30.63; 7032SC 3 x 18 in., $38.28; 7034SC 3 x 24 in., $47.85 |
Prices checked on eldoradotools.com on Nov 13, 2026, per piece. Each chisel is sold individually; where a minimum order applies, it is shown.
A scaling chisel and a tile chisel aren't the same tool, though many answers online treat them as one. A scaling chisel is a wide flat blade on a straight shank, built to shave. A tile chisel is wider and shorter, built to get under a tile and pop it. Both can lift floor tile; the next section covers when each one is the better pick.
Tile chisel or floor scraper for removing tile and thinset?
Tile on thinset, over a slab. Use the 3175TC tile chisel for a bathroom, a hallway or along walls, and a floor scraper for a whole room. The 3175TC is a 3 x 6-1/2 in. SDS-Plus tile chisel, $31.36. Start the blade at a grout line or a broken tile and drive it under the next tile.
Hold the hammer low, almost flat to the floor, so the edge rides along the slab instead of digging into it.
Thinset left on the slab is a separate step. After the tile comes up, take the ridges down with the floor scraper or a scaling chisel held low, then grind if the new floor needs it flat.
For a whole room or glued-down flooring, a floor scraper covers more floor per pass. The 2244FS is a 4 x 10 in. SDS-Plus scraper. The 7070FS is a 6 x 25 in. SDS-Max scraper, long enough to work standing up. The blade bolts on, so plan on a spare blade and a spare set of nuts and bolts. Hard use wears the blade edge and loosens the hardware, and the spares cost a fraction of a new scraper.
| Scraper | Spare blade | Spare nuts and bolts |
|---|---|---|
| 2244FS SDS-Plus, 4 x 10 in., $86.20 | FS-4B 4 in., $16.51 (min. 2) | FS-4NUT, $16.48 (min. 2) |
| 7070FS SDS-Max, 6 x 25 in., $341.82 | FS-6B 6 in., $15.62 (min. 2) | FS-6NUT, $26.74 |
Prices checked on eldoradotools.com on Nov 13, 2026, per piece. Each chisel is sold individually; where a minimum order applies, it is shown.
Wall tile on a mortar bed is a scaling chisel job, not a tile chisel job: see the scaling chisel table above. For the next step, drilling the new tile, read how to drill through tile.
How do plumbers trench a slab or chase a pipe?
Slab, saw-cut both sides, drain line below. Saw-cut both edges of the trench first, then break out the strip between the cuts with a bull point and a flat chisel, and clean the bottom with a scaling chisel. The saw cuts keep the break from running into the slab you're keeping. Diamond wheels for the cuts are in our concrete cutting collection.
On SDS-Max, use 18 in. parts so you work standing up: the 7005BP bull point, 18 in., $18.78 (min. 2); the 7015FC flat chisel, 1 x 18 in., $18.78 (min. 2); and the 7028SC scaling chisel, 2 x 18 in., $32.03. On SDS-Plus, use the 3118FC flat chisel, 3/4 x 18 in., $19.94 (min. 2). Its length keeps your hands up out of the trench, but keep SDS-Plus to short runs. For a footing or a foundation trench below grade, step up to the 24 in. SDS-Max set: the 7024BP bull point, 24 in., $34.86; the 7024FC flat chisel, 1 x 24 in., $34.86; and the 7029SC scaling chisel, 2 x 24 in., $36.20. Our foundation repair tools guide walks through the whole trench.
A pipe or conduit chase is a gouge chisel job. A gouge chisel has a curved blade that cuts a round-bottomed channel for the pipe to sit in. On SDS-Plus, use the 3120GC gouge chisel, 7/8 x 10 in., $29.61. On SDS-Max, for long or deep chases, use the 7075GC gouge chisel, 1 x 12 in., $50.16.
Data-center crews do the same work at scale: trenches and chases for conduit and drains, slab breakout for floor penetrations, and ground rods for the grounding system. The chisels, bull points and ground rod drivers in this guide are part of our data-center slab, rebar and demo collection. The 3150GR (5/8 x 10 in., SDS-Plus, $50.76) and 7050GR (7/8 x 10-1/4 in., SDS-Max, $88.14) drive ground rods without a sledge. ITM doesn't list which rod sizes each driver takes, so check the socket against your rod before you order. See everything we carry for the job on our data centers page.
SDS-Plus or SDS-Max chisels?
Match the chisel to the hammer you own. If you have both, use SDS-Max for slabs, trenches and whole floors, and SDS-Plus for tile, chases, tight spots and anything overhead. The difference is energy: Bosch rates its corded SDS-Plus hammers at 1.7 to 4.2 joules per blow, and its SDS-Max hammers at 8.5 to 19.
SDS-Max chisels don't cost more. A 12 in. SDS-Max bull point or flat chisel is $15.07, less than the $16.61 for a 10 in. SDS-Plus one, and ITM's own list prices run the same way. If your hammer takes SDS-Max, you get 2 more inches of reach for less money. Both are sold with a minimum of 2.
| Shank and length | Flat chisel price ($) |
|---|---|
| SDS-Plus 10 in. (3110FC) | 16.61 |
| SDS-Max 12 in. (7010FC) | 15.07 |
| SDS-Plus 18 in. (3118FC) | 19.94 |
| SDS-Max 18 in. (7015FC) | 18.78 |
| SDS-Max 24 in. (7024FC) | 34.86 |
How to read this: each bar is one flat chisel and its price per piece, checked Nov 13, 2026. The takeaway: at 10 to 12 in. and at 18 in., the SDS-Max chisel costs less than the SDS-Plus one. A bull point costs the same as the flat chisel at each of these lengths.
Don't chisel through an adapter. An SDS-Max to SDS-Plus adapter adds a joint between the hammer and the tool, and in hammer-only mode that joint takes the blows and loosens. Run each chisel in the hammer its shank was made for. More in our SDS-Max extension and adapter guide.
Which chisels only come in SDS-Max?
Six tools in this guide have no SDS-Plus version, because the job needs more energy than a 1 in. class hammer has: a clay spade, an asphalt cutter, an angled chisel, a seam tool and two bushing tools.
| Tool | Part | Use it for |
|---|---|---|
| Clay spade | 7065CS 5-3/8 x 16 in., $120.69 | Digging hard clay or hardpan around a footing, where a hand shovel won't cut |
| Asphalt cutter | 7055PH 3-1/2 x 16 in., $117.98 | Cutting clean edges in blacktop for a patch or a trench |
| Angled chisel | 7035AC 2 x 12 in., $39.31 | A 2 in. offset blade that sits flatter to the work, for edges along walls and in corners |
| Seam tool | 7060SM 1-1/8 x 12 in., $32.79 | A narrow, offset blade for cleaning out seams and joints |
| Bushing tool | 7045BT 1-7/8 x 9-7/8 in., $97.11 | Hammering a concrete surface rough so a patch or overlay can grip it |
| Carbide bushing tool | 7048CB 1-1/2 x 12 in., $120.26 | The same job with 25 carbide teeth, which stay sharp longer on big areas |
Prices checked on eldoradotools.com on Nov 13, 2026, per piece. Each chisel is sold individually; where a minimum order applies, it is shown.
How do you chisel concrete without the bit sticking or breaking?
Run the hammer in hammer-only mode, start at an edge, let the hammer do the work, and never pry. Most stuck and broken chisels come from one of these four mistakes.
- Hammer-only mode. Rotation on a chisel twists it in the hole, wears the shank and can snap a flat blade. Set the mode before you start, and don't switch it with the motor running.
- Lock the angle. Turn the chisel so the blade lines up with the cut you want, then lock it. A blade that's off by a few degrees fights you on every blow.
- Work from an edge. Take bites a few inches back from an edge or a crack. A chisel driven into the middle of solid concrete has nowhere to push the pieces, and it sticks.
- Don't pry. Hilti warns that levering with a chisel can bend or break the shank. If the chisel sticks, stop, switch off, and work it out by hand, or free it with a second chisel.
A worn chisel works slower and heats up faster. When the tip rounds over or starts to mushroom, have it reground by a shop that sharpens demolition steel. Hilti's guidance is not to let the tip overheat while grinding: if the steel turns blue, it has lost its hardness.
Chipping concrete makes silica dust. OSHA's construction silica standard (29 CFR 1926.1153, Table 1, row x) covers handheld powered chipping tools. It lists two controls: water sprayed at the point of impact, or a dust shroud on a vacuum with a 99% filter. With either one, no respirator is required outdoors for up to 4 hours a shift; indoors, or past 4 hours outdoors, the minimum is a respirator with an assigned protection factor of 10. Wear hearing and eye protection on every job.
"If your hammer takes SDS-Max, buy the Max point and flat. They cost less than the SDS-Plus ones and give you two more inches. A tile setter gets the 3175TC and a floor scraper with a spare blade. A foundation crew gets the 18 and 24 in. Max sets, so nobody works on their knees in the trench."
David Castro, President, Eldorado Tools
SDS chisel sizes and prices
Every SDS chisel in this guide, by shank and type. Sizes are ITM's, from its 2026 catalog.
| Part | Shank | Type | Size (width x length) | Price |
|---|---|---|---|---|
| 2100BP | SDS-Plus | Bull point | 5-1/2 in. | $15.13 (min. 2) |
| 3100BP | SDS-Plus | Bull point | 10 in. | $16.61 (min. 2) |
| 2110FC | SDS-Plus | Flat chisel | 3/4 x 5-1/2 in. | $16.78 (min. 2) |
| 3110FC | SDS-Plus | Flat chisel | 3/4 x 10 in. | $16.61 (min. 2) |
| 3118FC | SDS-Plus | Flat chisel | 3/4 x 18 in. | $19.94 (min. 2) |
| 2115SC | SDS-Plus | Scaling chisel | 1-1/4 x 5-1/2 in. | $21.04 (min. 2) |
| 3115SC | SDS-Plus | Scaling chisel | 1-1/2 x 10 in. | $30.89 |
| 3122SC | SDS-Plus | Scaling chisel | 2-1/2 x 10 in. | $35.52 |
| 3175TC | SDS-Plus | Tile chisel | 3 x 6-1/2 in. | $31.36 |
| 3120GC | SDS-Plus | Gouge chisel | 7/8 x 10 in. | $29.61 |
| 2244FS | SDS-Plus | Floor scraper | 4 x 10 in. | $86.20 |
| 3150GR | SDS-Plus | Ground rod driver | 5/8 x 10 in. | $50.76 |
| 7000BP | SDS-Max | Bull point | 12 in. | $15.07 (min. 2) |
| 7005BP | SDS-Max | Bull point | 18 in. | $18.78 (min. 2) |
| 7024BP | SDS-Max | Bull point | 24 in. | $34.86 |
| 7010FC | SDS-Max | Flat chisel | 1 x 12 in. | $15.07 (min. 2) |
| 7015FC | SDS-Max | Flat chisel | 1 x 18 in. | $18.78 (min. 2) |
| 7024FC | SDS-Max | Flat chisel | 1 x 24 in. | $34.86 |
| 7020SC | SDS-Max | Scaling chisel | 1-1/2 x 12 in. | $23.39 (min. 2) |
| 7025SC | SDS-Max | Scaling chisel | 2 x 12 in. | $24.45 (min. 2) |
| 7028SC | SDS-Max | Scaling chisel | 2 x 18 in. | $32.03 |
| 7029SC | SDS-Max | Scaling chisel | 2 x 24 in. | $36.20 |
| 7030SC | SDS-Max | Scaling chisel | 3 x 12 in. | $30.63 |
| 7032SC | SDS-Max | Scaling chisel | 3 x 18 in. | $38.28 |
| 7034SC | SDS-Max | Scaling chisel | 3 x 24 in. | $47.85 |
| 7035AC | SDS-Max | Angled chisel | 2 x 12 in. | $39.31 |
| 7075GC | SDS-Max | Gouge chisel | 1 x 12 in. | $50.16 |
| 7070FS | SDS-Max | Floor scraper | 6 x 25 in. | $341.82 |
| 7050GR | SDS-Max | Ground rod driver | 7/8 x 10-1/4 in. | $88.14 |
| 7060SM | SDS-Max | Seam tool | 1-1/8 x 12 in. | $32.79 |
| 7045BT | SDS-Max | Bushing tool | 1-7/8 x 9-7/8 in. | $97.11 |
| 7048CB | SDS-Max | Carbide bushing tool | 1-1/2 x 12 in. | $120.26 |
| 7065CS | SDS-Max | Clay spade | 5-3/8 x 16 in. | $120.69 |
| 7055PH | SDS-Max | Asphalt cutter | 3-1/2 x 16 in. | $117.98 |
Prices checked on eldoradotools.com on Nov 13, 2026, per piece. Spare floor scraper blades and hardware are listed in the floor scraper section above. Browse all SDS-Plus chisels and SDS-Max chisels.
FAQ
Why does my SDS chisel keep getting stuck?
It's usually driven too deep in one spot, away from an edge. Take smaller bites a few inches back from an edge or a crack so the pieces have somewhere to go, and don't lean on the hammer. If it sticks, switch off and work it free by hand rather than prying.
Why is the tip of my chisel mushrooming?
The steel is wearing and heating, usually from long runs in one spot or a dull tip. Have the chisel reground before the mushroom gets big, and keep the tip from turning blue while it's ground.
Can I sharpen an SDS chisel myself?
Hilti recommends having demolition chisels reground by a shop that sharpens them. If you grind one yourself, keep the steel cool: a tip that turns blue has lost its hardness.
Why do floor scraper bolts keep coming loose?
Every blow from the hammer shakes the hardware. Check the nuts at each break, and keep a spare kit on hand: FS-4NUT for the 2244FS, FS-6NUT for the 7070FS.
What are MINI chisels for?
The MINI SDS-Plus chisels (2100BP, 2110FC and 2115SC) are 5-1/2 in. long, so the hammer fits under a vanity, beside a toilet flange or inside a cabinet where a 10 in. chisel won't.
Which ground rod driver fits my rod?
ITM lists the 3150GR as 5/8 x 10 in. and the 7050GR as 7/8 x 10-1/4 in., but doesn't say which rod sizes each one takes. Check the socket against your rod before you order, or call us.
Can I use an SDS-Plus chisel in an SDS-Max hammer?
Only with an adapter, and we don't recommend chiseling through one: the joint takes the blows and loosens. Use a chisel with the same shank as the hammer.
Not sure which chisel fits the job? Call our team at (833) 4-ETOOLS or email sales@eldoradotools.com with what you're removing, what's under it and the hammer you have, and we'll name the part.
Related: SDS Plus vs SDS Max, foundation repair tools, concrete core drill bits and drilling through rebar.
Sources: ITM 2026 catalog, pp. 102–103 (sizes); Bosch 11236VS and 11245EVS, Milwaukee 5268-21 and 5314-21, and Makita HR4002 and HR4003C rotary hammer manuals (hammer-only mode, angle lock, mode changes); Bosch Professional SDS-plus and SDS-max product pages (impact energy); Hilti chisel information and resharpening guidelines; OSHA 29 CFR 1926.1153, Table 1. Prices from eldoradotools.com on Nov 13, 2026.
First published [date], with prices checked on Nov 13, 2026.






























































































































